Panasonic TX-51P100X, Руководство по обслуживанию

Страница: 54 / 108

- 54 -
Schematic Diagram
Components identified by mark have special characteristics important for safety.
When replacing any of these components, use only manufacture's specified parts.
Important Safety Notice
Notes:
1.
Resistor
All resistors are cabon 1/4W resistor, unless marked as follows:
Unit of resistance is OHM [
W
] (K=1,000, M=1,000,000).
: Nonflammable : Metal Oxide
: Solid : Metal Film
: Wire Wound : Fuse
:
2.
Capacitor
All capacitors are ceramic 50V capacitor, unless marked as follows:
Unit of capacitance is
m
F, unless otherwise noted.
: Temperature Compensation : Electrolytic
: Polyester : Bipolar
: Metalized Polyester : Dipped Tantalum
: Polypropylene : Z-Type
3. Coil
Unit of inductance is
m
F, unless otherwise noted.
4. Test Point
: Test Point position
5. Earth Symbol
: Chassis Earth (Cold) : Line Earth (Hot)
6. Voltage Measurement
Voltage is measured by a DC voltmeter.
Conditions of the measurement are the following:
Power Source ................................................... AC 220V, 50Hz
Receiving Signal ............................................... Colour Bar signal (RF)
All customer's controls ...................................... Maximum positions
7. Number in red circle indicates waveform nember.
(See waveform pattern table.)
8. When arrow mark ( ) is found, connection is easily found from the direction of arrow
9. Indicates the major signal flow. : Video Audio Pin P Video
10. This schematic diagram is the latest at the time of printing and subject to change without
notice.
Remarks:
1. The Power Circuit contains a circuit area which uses a separate power supply to isolate the
earth connection.
The circuit is defined by HOT and COLD indications in the schematic diagram. Take the
follwing precautions.
All circuits, except the Power Circuit, are cold.
Precautions
a. Do not touch the hot part or the hot and cold parts at the same time or you may
be shocked.
b. Do not short- circuit the hot and cold circuits or a fuse may blow and parts may
break.
c. Do not connect an instrument, such as an oscilloscope, to the hot and cold
circuits simultaneously or a fuse may blow.
Connect the earth of instruments to the earth connection of the circuit being
measured.
d. Make sure to disconnect the power plug before removing the chassis.
2. Following diodes are interchangeable.
MA150- MA162 (Replacement part)
+ -
M
m T
Z
NP
Audio Block/ Schematic Diagram, Remote Control.
Remote Control Transmitter TNQE194
Key Function Table
Key
No.
Function
Key
No.
Function
Key
No.
Function
1 MUTE 23 MAIN MENU 45 P.AI
2 SURROUND 24 CH 4 46 HOLD
3 TV/AV 25 CH 9 47 STEREO
4 VCR/LD:REW 26 CH 8 48 TV/TEXT
5 VCR/LD:STOP 27 VOL. UP 49 YELLOW
6 VCR/LD:FF 28 N (NORNAL) 50 GREEN
7 VCR/LD:PLAY 29 RIGHT 51 BLUE
8 VCR/LD:POWER ON/OFF 30 VCR:CH UP/LD:SKIP + 52 RED
9 CH 3 31 LEFT 53 REVEAL
10 CH 2 32 CH 7 54 F/T/B
11 POS. UP 33 2 DIGIT 55 F.P.
12 LD FUNCTION 34 CH 0 56 P.AI
13 VCRADVANCE/LD:DISC A 35 VOL. DOWN 57 --------
14 VCR:REC/LD:DISC B 36 DOWN 58 --------
15 VCR FUNCTION 37 PC 59 --------
16 CH 1 38 VCR:CH DOWN/LD:SKIP - 60 GREEN
17 CH 6 39 OFF TIMER 61 YELLOW
18 CH 5 40 RECALL 62 BLUE
19 POS. DOWN 41 INDEX 63 RED
20 UP 42 F/T/B 64 POWER ON/OFF
21 VCR/LD:PAUSE 43 HOLD
22 VCR:REC 44 D.PNR
1
2
3
4
6
5
10
7
11
8
9
27
25
24
20
18
23
28
26
19
22
21
12 17
IC1001
13
14
16
15
X1001
C1002
J1001
D1005
C1001
Q1001
D1001
R1001
8
1
2
3
4
5
6
7
16
9
10
11
12
13
14
15
24
17
18
19
20
21
22
23
32
25
26
27
28
29
30
31
40
33
34
35
36
37
38
39
48
41
42
43
44
45
46
47
56
49
50
51
52
53
54
55
57
58
59
60
61
VDD
2.2 - 3.5V
D1004
D1003
TP1
TP3
TP2
TP7
TP8
TP9
TP10
TP11
TP12
TP5 TP6
TP13
TP14
TP15
TP16
TP17
TP18
TP19
TP20
POD2
POD3
INT
POE0
POE1
POE2
POE3
REM
VDD
XOUT
XIN
GND
RST
WOOUT
POD1
POD0
POC3
POC2
POC1
POC0
POB3
POB2
POB1
POB0
POA3
POA2
POA1
POA0
TP4
62
63
64
D1002