Panasonic TH152UX1 - 152" PLASMA TV, Руководство по обслуживанию, Страница: 10 / 127

10
TH-152UX1 / TH-152UX1W / TH-152UX1C
4 Specifications
Power Source 200-240 V AC, 50/60Hz
Power Consumption
Power on 3700W
Stand-by condition 0.5 W
Power off condition 0.3 W
Plasma Display panel Drive method : AC type
152-inch, 17:9 aspect ratio
Screen size 134.4 inch (3,416 mm) (W) x 70.9 inch (1,801 mm) (H) x 152.0 inch(3,862 mm) (diagonal)
(No. of pixels) 8,847,360 (4,096 (W) x 2,160 (H))
[4,096 x 2,160 x 3 dots]
Operating condition
Temperature 32
°
F - 95
°
F (0
°
C - 35
°
C)
Humidity 20 % - 80 %
Applicable signals
Scanning format
525 (480) / 60i 60p, 625 (575) / 50i 50p, 750 (720) / 60p 50p, 1125 (1080) /
60i 60p 50i 50p 24p 25p 30p 24sF, 1250 (1080) / 50i
PC signals VGA, SVGA, XGA, SXGA
UXGA ..... (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
Connection terminals
AV IN HDMI 1/2 TYPE A Connector x 2
HDMI (Version 1.4 with 3D)
SDI IN
*1 BNC
HD-SDI (Dual Link) x 4, 4K signal input 0.8 Vp-p (75-ohm)
DVI-D IN
*1
DVI-D (Single Link) 24 Pin x 4, 4K signal input Compliance with DVI Revision 1.0
PC IN High-Density Mini D-sub 15 Pin G with sync 1.0 Vp-p (75-ohm)
G without sync 0.7 Vp-p (75-ohm)
B: 0.7 Vp-p (75-ohm)
R: 0.7 Vp-p (75-ohm)
HD/VD: 1.0 - 5.0 Vp-p (high impedance)
VBS (use HD port) with picture 1.0 Vp-p (high impedance)
without picture 0.3 Vp-p (high impedance)
SERIAL External Control Terminal
D-sub 9 Pin
RS-232C compatible
3D SHUTTER OUT
*2
M3 jack x 1, for 3D active shutter eyewear
SLOT DVI-D IN DVI-D 24 Pin
Content Protection
Audio Input is not available
Compliance with DVI Revision 1.0
Compatible with HDCP 1.1
Accessories Supplied
Remote Control
Transmitter N2QAYB000560 (UX1, UX1W) , N2QAYB000561 (UX1C)
Batteries R6(AA)Size x 2
Fixing band TMME203 x 3
Dimensions (W
×
H
×
D)
141.8 inch x 78.0 inch x 5.8 inch
*3
/ 3,600 mm x 1,980 mm x 147 mm
*3
Mass (weight) approx. 1,272.1 lbs / 577 kg net
*1 4 inputs is set and only for one 4k2k signal. You can not input 4 different signal to each inputs.
*2 An optional 3D IR TRANSMITTER is required for viewing 3D images.
*3 10.3 inch / 260 mm when including protruding portion of terminals
Note:
• Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
• This equipment complies with the EMC standards listed below.
EN55022, EN55024, EN61000-3-11, EN61000-3-12.