Panasonic TH-85PF12E Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 66

Panasonic TH-85PF12E Скачать руководство пользователя страница 7

+

+

-

-

7

Accessories Supply

Accessories

Clamper × 1

Eyebolt cap × 1

Blind sheet × 1

Allen wrench

Eyebolt × 1
(M12)

Ferrite core × 2

Noise cut

fi

lter

Batteries for
the Remote
Control
Transmitter
(R6(UM3) Size
× 2)

Power supply
cord

Fixing band
× 2

Remote Control
Transmitter
EUR7636090R

Operating
Instruction
book

Check that you have the accessories and items shown

Remote Control Batteries

Use the clamper
when connecting a
LAN cable.
(see page 59)

Helpful Hint:

For frequent remote control users, replace old batteries with Alkaline
batteries for longer life.

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.
Disposal of batteries should be in an environment-friendly manner.

Observe the following precaution:

1. Batteries shall always be replaced as a pair. Always use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5. Battery replacement is necessary when remote control acts sporadically or stops operating the Plasma Display set.
6. Do not burn or breakup batteries.
Batteries must not be exposed to excessive heat such as sunshine,

fi

re or the like.

CD-ROM
(Operating
instructions)

Requires two R6 batteries.

1. Pull and hold the hook, then open

the battery cover.

2. Insert batteries - note correct

polarity ( + and -).

3. Replace the cover.

“R6 (UM3)” size

Use the Ferrite cores and Noise cut

fi

lter to

comply with the EMC standard. (see page
59)

«
...
5
6
7
8
9
...
»

Содержание TH-85PF12E



































































Отзывы:

Нет отзывов