Panasonic TH-55SF2U, Инструкция по эксплуатации - Базовое руководство

Страница: 9 / 28

9
English
Precautions for use
Cautions when installing
Do not set up the Display outdoors.
•
The Display is designed for indoor use.
Install this unit at a location which can support the
weight of the unit.
•
Use the installation bracket that conforms to VESA
standards
Environmental temperature to use this unit
•
When using the unit where it is below 1 400 m (4 593
ft) above sea level: 0 °C to 40 °C (32 °F to 104 °F)
•
When using the unit at high altitudes (1 400 m (4 593
ft) and higher and below 2 800 m (9 186 ft) above sea
level): 0 °C to 35 °C (32 °F to 95 °F)
Do not install the unit where it is 2 800 m (9 186 ft)
and higher above sea level.
•
Failure to do so may shorten the life of the internal
parts and result in malfunctions.
We are not responsible for any product damage, etc.
caused by failures in the installation environment
even during the warranty period.
Required space for ventilation
•
When using the pedestal, leave a space of 10 cm
(3
15/16
”) or more at the top, left and right, and 5 cm
(1
31/32
”) or more at the rear, and also keep the space
between the bottom of the display and the floor
surface.
If using some other setting-up method (wall-hanging,
etc.), follow the manual of it. (If there is no specific
indication of installation dimension in the installation
manual, leave a space of 10 cm (3
15/16
”) or more at
the top, bottom, left and right, and 5 cm (1
31/32
”) or
more at the rear.)
Minimum distance:
a
a b a: 10 cm
(3
15/16
”)
b: 5 cm
(1
31/32
”)
a
•
Operation of this unit is guaranteed up to an ambient
temperature of 40 °C (104 °F). When installing the
unit in a case or chassis, be sure to provide adequate
ventilation with a cooling fan or ventilation hole so
that the surrounding temperature (inside the case or
chassis) including the temperature of the front surface
of the liquid crystal panel can be kept at 40 °C (104 °F)
or less.
About the screws used when using a wall hanging
bracket that conforms to VESA standards
65-inch model 55-inch model
49-inch model 43-inch model
Screw pitch for
installation
Depth of
screw hole
Screw
(quantity)
400 mm × 400 mm 10 mm M6 (4)
Be careful of the movable structure of the power
indicator and remote control sensor.
•
As factory default, the power indicator and remote
control sensor are stored in the main unit. For normal
use, pull out the remote control sensor from the edge
side of the main unit by operating the lever on the
rear panel. Depending on the setup condition such as
when using the multi display, store the remote control
sensor in the main unit. (see page 17)
Do not grab the liquid crystal panel.
•
Do not forcibly press the liquid crystal panel, or push
it with a pointed object. Applying a strong force to
the liquid crystal panel will cause unevenness of the
screen display, resulting in malfunction.
Depending on the temperature or humidity
conditions, uneven brightness may be observed.
This is not a malfunction.
•
This unevenness will disappear while applying current
continuously. If not, consult the distributor.
Notes on Using Wired LAN
When setting up the Display at a place, where
electric statistic occurs often, take a sufficient
antistatic measure before start using.
•
When the Display is used at a location, where static
electricity occurs often, such as on a carpet, a wired
LAN or DIGITAL LINK communication is disconnected
more often. In that case, remove static electricity
and the noise source that may cause problems with
an antistatic mat, and re-connect the wired LAN or
DIGITAL LINK.
•
In rare cases, the LAN connection is disabled due
to static electricity or noise. In that case, turn off the
power of the Display and the connected devices once
and then re-turn on the power.
The Display may not work properly due to strong
radio wave from the broadcast station or the radio.
•
If there is any facility or equipment, which outputs
strong radio wave, near the installation location, set
up the Display at a location sufficiently far from the
source of the radio wave. Or, wrap the LAN cable
connected to the DIGITAL LINK / LAN terminal by
using a piece of metal foil or a metal pipe, of which is
grounded at both ends.