background image

15V line SOS

P(Multi/SS), D, DN,SS,PB,DR1/2 Board

Trouble Mode

Defective Board

Panel SOS – Power LED Blinks 2 Times (SS Side)

How to find the defective board

DN

IC4701

D

D3

8

PANEL_SOS

IC9003

67

DN

2

8

166

15V

P(Multi/SS)

PC

Power Supply / Protect Circuit

Q9050

Q9051

15V SOS

71

PB

15

15

15V

DC

CONV.

DC

CONV.

1

PB31

15V

15V

1

P5

15V

1
2

P25

1
2

PC

202

D25

1
2

1
2

PC

201

SS

DR2

DR

11

SS

35

SS

42

DR1

DR

1

15V

P12

4

SS

12

Note: The check position is the connector on the board , 

not cable's connector.

Yes

Yes

No

Yes

No

P(SS) Board

Yes

No

DN Board

No

PB

Board

Is pin 1 of 

Socket P25 shorted

to GND?

Yes

No)

Yes

DR2 Board

No

Yes

DR1 Board

No

SS Board

DN Board

Yes

D Board

No

Disconnect the unit 

from AC Power

Is pin 1 of 

socket D25 shorted

to GND?

Is pin 15 of 

socket DN2 shorted

to GND?

Is pin 15 of

socket DN2 shorted

to GND?

Is Test Point TP15V

on the SS board shorted to 

GND?

Is Test Point TP15V

on the SS board shorted

to GND?

Is pin 4 of

socket P12 shorted 

to GND?

Is pin 1 of 

socket P5 shorted to 

GND?

P(SS) 
Board

SS Side Troubleshooting

25

Disconnect CN P25. 

Disconnect CN D25. 

Disconnect CN DN2. 

Disconnect CN P12 

Disconnect CN SS35 

Disconnect CN P5

Disconnect CN SS42

Disconnect CN DN2

Содержание TH-103PF9UK - 103" Plasma Panel





























































Отзывы: