manualshive.com logo in svg

Panasonic TC-P42C1 - 41.6" Plasma TV, Исправленное руководство по устранению неисправностей

Поделиться
Скачать
Panasonic TC-P42C1 - 41.6

Slide #2

Prepared by

Cesar Perdomo

Panasonic Service and Technology  Company

National Training 

 Warning 

This service information is designed for experienced repair technicians only and is not designed for use by the 
general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in 
attempting to service a product. Products powered by electricity should be serviced or repaired only by 
experienced professional technicians. Any attempt to service or repair the product or products dealt with in this 
service information by anyone else could result in serious injury or death. 

 

Copyright 

©

 

2009 by Panasonic Service and Technology Company

All rights reserved.  Unauthorized copying and distribution is a violation of law.

"HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.“

Содержание TC-P42C1 - 41.6" Plasma TV








































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды