RQ
T999
5
20
“--:--”
• You connected the AC mains lead for the first time or
there was a power failure recently. Set the clock.
“Adjust Clock”
• Clock is not set. Adjust the clock accordingly.
“Adjust Timer”
• Play timer is not set. Adjust the play timer accordingly.
“Auto Off”
• The unit has been left unused for about 20 minutes
and will shut down in a minute. Press any button to
cancel it.
“Checking Connection”
• The unit is checking the connected iPhone/iPad/iPod
or USB device.
• If this display keeps appearing, make sure that the
battery of the iPhone/iPad/iPod is not depleted and
that the iPhone/iPad/iPod is turned on and connected
correctly.
“DL Error”
• The software download has failed. Press any button to
exit. Please try again later.
• The server cannot be found. Press any button to exit.
Make sure that the wireless network is connected to
the Internet.
“Error”
• An incorrect operation was done. Read the instructions
and try again.
“F
” / “F
” (“
” stands for a number.)
• There is a problem with this unit.
Write down the displayed number, disconnect the AC
mains lead and consult your dealer.
“Fail”
• Updating or setting has failed. Read the instructions
and try again.
“Level 0”
• There is no link between this system and the wireless
router.
Try the following operations:
j
Check that the wireless router is turned on.
j
Turn this system off and on again.
j
Reset the wireless network settings. (
>
6)
If the problem persists, consult your dealer.
“Linking”
• This system is trying to connect to the last connected
Bluetooth
®
device when “BLUETOOTH” is selected.
• This system is communicating with the wireless router
to complete the network settings.
Depending on the wireless router this process may
take a few minutes. Try moving this system closer to
the wireless router.
“Network Initializing”
“Setup in Progress, Try Again”
• The system is carrying out an internal process.
– Wait for approximately 3 minutes.
– Do not disconnect the AC mains lead. Doing so may
cause malfunction.
“No Connect”
• This system cannot connect to the network.
Check the network connection. (
>
6)
“No Device”
• The iPhone/iPad/iPod or USB device is not connected.
Examine the connection.
• The battery of the iPhone/iPad/iPod is depleted.
Charge the iPhone/iPad/iPod and turn it on before
connecting.
“No Disc”
• You have not put in a disc or put in a disc that the
system cannot play.
“No Memory” (
[PMX100B]
)
• There are no preset DAB stations to select. Preset
some channels.
“No Play”
• Examine the content. You can only play supported
format.
• The files in the USB device can be corrupted. Format
the USB device and try again.
• The unit may have a problem. Turn the unit off and
then on again.
“No Signal” (
[PMX100B]
)
• This station cannot be received. Check your antenna.
“Device No Response”
“Hub Not Supported”
“Not Supported”
• You have connected an iPhone/iPad/iPod that cannot
be played.
• If the iPhone/iPad/iPod is compatible, turn it on and
connect it correctly.
• You have connected an unsupported USB device.
“PC Unlocked”
• “PC” is selected, but a PC is not connected.
“PGM Full”
• The number of programmed tracks is more than 24.
“Playerror”
• You played an unsupported file. The system will skip
that track and play the next one.
“Reading”
• The unit is checking the CD information. After this
display has disappeared, start operating.
“Remote
” (“
” stands for a number.)
• The remote control and this unit are using different
codes. Change the code on the remote control.
– When “Remote 1” is displayed, press and hold [OK] and
[1] for at least 4 seconds.
– When “Remote 2” is displayed, press and hold [OK] and
[2] for at least 4 seconds.
“Scan Failed” (
[PMX100B]
)
• Stations are not receivable. Check your antenna and try
DAB manual tuning.
“USB Over Current Error”
• The iPhone/iPad/iPod or USB device is drawing too
much power. Remove the iPhone/iPad/iPod or USB
device. Switch the system off and on again.
“VBR”
• The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
“WAC Mode”
• “Method 1” of network setting method is available.
(
>
6)
• To exit “WAC Mode”, press [
∫
].
“Wait”
• This is displayed, for example, when this unit is turning
off.
• This is flashing when the system is trying to enter a
network setting mode.
“
” blinks
• This may occur when, for instance, the network
connection is interrupted.
Main unit displays
SC-PMX100-100B_EGEBGN-RQT9995-B.book 20 ページ ２０１５年４月２０日 月曜日 午後３時４５分
