Panasonic SC-HG1-C Скачать руководство пользователя страница 11

Страница: 11 / 128

Before Using This Product

WUME-SCHG1C-4

1-3

1-2 Safety information

WARNING

●

Never use this product as a sensing device for personnel protection.

●

When using sensing devices for personnel protection, use products that meet the laws and stan-

dards for personnel protection that apply in each region or country, such as OSHA, ANSI and IEC.

Specifications

●

This product has been developed / produced for industrial use only.

● Do not use this product under conditions outside the specified ranges. Risk of an accident

and product damage.There is also a risk of a significant reduction of service life.

Power supply

●

Incorrect wiring will damage the internal circuitry. Check the wiring before turning ON the

power.

● Verify that power supply fluctuations are within the rating.

●

Risk of damage and burning if a voltage over the rating is applied, or AC power is directly ap-

plied.

●

If power is supplied from a commercial switching regulator, ensure that the frame ground

(F.G.) terminal is connected to an actual ground.

● Ensure that there is sufficient leeway in the voltage source capacity.

●

Do not use during the initial transient time after the power supply is switched ON

For details, refer to

“4-5 Initial operation after power is turned ON”

●

Use an isolation transformer in the DC power supply. Risk of short-circuiting and damage to

the product or power supply if an auto transformer is used.

●

If surges occur in the power supply, connect a surge absorber to the source to absorb the

surges.

Wiring

●

Make sure that the power is OFF while performing wiring or connection work. Risk of electric

shock or product damage.

●

Risk of damage and burning if the load is incorrectly wired or short-circuiting occurs.

●

When noise generating equipment (switching regulator, inverter motor, etc.) is used in the vi-

cinity of this product, connect the frame ground (F.G.) terminal of the equipment separately to

ground.

●

To avoid noise, keep the wiring as short as possible.

●

Do not wire in parallel with a high-voltage line or power line, or run through the same conduit.

Risk of malfunctioning due to induction.

● For the communication cable, use a dedicated cable that is certified by CC-Link Partner As

sociation.

● For detailed grounding specifications, refer to the installation manual published by the CC-

Link Partner Association.

Usage environment

●

This product is suitable for indoor use only.

●

Avoid dust, dirt, and steam.

●

Do not use in locations where there are corrosive or other harmful gases.

●

Ensure that the product does not come into contact with organic solvents such as thinner.

●

Ensure that the product does not come into contact with strong acid or alkaline.

●

Ensure that the product does not come into contact with oil or grease.

● This product cannot be used in an environment that contains flammable or explosive gases.

● Performance may not be satisfactory in a strong electromagnetic field.

●

Do not drop or otherwise subject to shock. Risk of product damage.

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 11 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: