Panasonic SC-HG1-C Скачать руководство пользователя страница 63

Страница: 63 / 128

CC-LINK Network Communication

WUME-SCHG1C-4

4-29

4-5 Initial operation after power is turned ON

After the power is turned on, the communication unit cannot start communication until it completes

initial transient processing such as initialization.

When the unit is ready for communication after the power is turned on, the RX[7B]: remote

ready flag (*1) bit is automatically set.

Check that the RX[7B]: remote ready flag (*1) bit is set before executing communication.

Communication starts

Transient state

RX[7B] (*1)

Check remote ready flag

Communication unit

power

When initialization is completed after the power is turned ON, the RX[7B]: remote ready

flag (*1) is automatically set.

If the RX[7B]: remote ready flag (*1) is not set after the power is turned ON, startup may have

failed.

Check the communication unit connection and settings, and turn on the power again.

*1: The bit position depends on the operation mode.

CC-Link mode 1: RX[7B], CC-Link mode 2: RX[17B], CC-Link mode 3: RX[1BB]

Содержание SC-HG1-C

































































































































Результаты поиска

Содержание SC-HG1-C

Отзывы:

Panasonic SC-HG1-C, Руководство пользователя, Страница: 63 / 128

Результаты поиска

Содержание SC-HG1-C

Отзывы: