manualshive.com logo in svg

Panasonic SC-HC05GN, Руководство по обслуживанию

Поделиться
Скачать
Panasonic SC-HC05GN Скачать руководство пользователя страница 5

5

1.3.

Before Repair and Adjustment

Disconnect AC power, discharge unit AC Capacitors as such C702, C710, C725, C727 and C728 through a 10W, 1W resistor to
ground.
Caution : DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
After repairs are completed, restore power gradually using a variac, to avoid overcurrent.

• Current consumption at AC 220V-240V, at 50Hz in NO SIGNAL mode, at volume minimum. (For GN) 

• Current consumption at AC 110V-240V, at 50/60Hz in NO SIGNAL mode, at volume minimum. (For GS) 

1.4.

Caution For Fuse Replacement

1.5.

Protection Circuitry

The protection circuitry may have operated if either of the following conditions are noticed:

• No sound is heard when the power is turned on.
• Sound stops during a performance.

The function of this circuitry is to prevent circuitry damage if, for example, the positive and negative speaker connection wires are
"shorted", or if speaker systems with an impedance less than the indicated rated impedance of the amplifier are used.
If this occurs, follow the procedure outlines below:

1. Turn off the power.
2. Determine the cause of the problem and correct it.
3. Turn on the power once again after one minute.

Note:
When the protection circuitry functions, the unit will not operate unless the power is first turned off and then on again.

1.6.

Safety Part Information

Safety Parts List:

There are special components used in this equipment which are important for safety.
These parts are marked by   in the Schematic Diagrams, Exploded View & Replacement Parts List. It is essential that these
critical parts should be replaced with manufacturer’s specified parts to prevent shock, fire or other hazards. Do not modify the
original design without permission of manufacturer.

Table 1

Safety

Ref. No.

Part No.

Part Name & Description

Remarks

61

VUEMNPHC05GN

NAME PLATE

GN-K/W

61

VUEMNPHC05GS

NAME PLATE

GS-W

A1

K2CZ3YY00005

AC CORD (3PIN)

GS

A1

K2CQ2CA00007

AC CORD (2PIN)

GS

A1

K2CJ2DA00010

AC CORD

GN

A1

K2CP2CA00001

AC CORD (with TAG)

GS

A3

RQTX1318-B

O.I BOOK (En)

GN/GS

A3

RQTX1321-G

O.I BOOK (Cn Ar)

GS

PCB3

VUEESBDHC05E

SMPS P.C.B

W1

VUEM0102HC05

1P WHITE WIRE (W1A/W1B)

W2

VUEM0103HC05

1P BLACK WIRE (W2A/W2B)

F751

VUEEFHC05

FUSE

P751

VUEEAIHC05E

AC INLET

Содержание SC-HC05GN






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды