31
RQT9464
Network settings
These settings are used if you will connect this unit to the Internet. (
>
38)
≥
The connection to the Internet may take time or the Internet may not be connected depending on the connection environment.
It is required that you use a broadband connection.
Preparation
≥
Connect to a broadband network. (
>
11)
Testing of “IP Address / DNS Settings”
Always test the connection when a LAN cable is connected.
1
While stopped
Press [BD/SD] to select “BD/DVD”.
2
Press [SETUP].
3
Press [
3
,
4
] to select “Network Settings” and
press [OK].
4
Press [
3
,
4
] to select “IP Address / DNS
Settings” and press [OK].
5
Press [
3
,
4
] to select “Connection Test” and
press [OK].
“Testing...”: The test is in progress.
“Pass”:
The connection is completed.
Press [RETURN] to exit.
“Fail”:
Please check the connection and settings.
≥
Perform the “Connection Test” also when any
change was made to the “IP Address / DNS
Settings”.
≥
If the connection test fails, it may be necessary to set the
MAC address of this unit at the router side. The MAC
address can be displayed by pressing [SETUP] and
selecting “Network Settings”.
N
R
U
T
E
R
K
O
IP Address/DNS Settings
Connection Test
On
On
On
On
On
On
IP Address Auto-Assignment
DNS-IP Auto-Assignment
IP Address
Subnet Mask
Gateway Address
Primary DNS
Secondary DNS
Connection Speed Auto-Config
Connection Speed Setting
NOTE
RETURN
Network Settings
IP Address / DNS Settings
Proxy Server Settings
MAC Address: xx-xx-xx-xx-xx-xx
OK
Network Service
Setting the IP address
In most cases, default settings can normally be used
without making any changes.
Set the IP address only when the router has no DHCP
server functions or when the router’s DHCP server
function is disabled.
After performing steps
1
–
4
(
D
left)
5
Press [
3
,
4
] to select “IP Address
Auto-Assignment” and press [
2
,
1
] to select
“Off”.
6
Press [
3
,
4
] to select “IP Address”, “Subnet
Mask” or “Gateway Address” and press [OK].
7
Enter numbers with the numbered buttons and
press [OK].
≥
After checking the specifications for your broadband
router, enter each number.
If the number is unknown, then check the number of
other devices such as personal computers connected
via a LAN cable. Assign a different number from those
of other devices for the “IP Address” and the same
number for others.
≥
If a wrong number is entered, then press [CANCEL].
8
Press [
2
,
1
] to select “Yes” and press [OK].
≥
The numeric input range is between 0 and 255.
Setting the DNS-IP
In most cases, default settings can normally be used
without making any changes.
When setting an assigned DNS server from your Internet
service provider, perform the following settings.
After performing steps
1
–
4
(
D
left)
5
Press [
3
,
4
] to select “DNS-IP
Auto-Assignment” and press [
2
,
1
] to select
“Off”.
6
Press [
3
,
4
] to select “Primary DNS” or
“Secondary DNS”and press [OK].
7
Enter numbers with the numbered buttons and
press [OK].
≥
Follow the instructions given by your Internet service
provider and enter the numbers.
If the number is unknown, then check the number of
other devices such as personal computers connected
via a LAN cable and assign the same number.
≥
If a wrong number is entered, then press [CANCEL].
8
Press [
2
,
1
] to select “Yes” and press [OK].
≥
The numeric input range is between 0 and 255.
NOTE
192
.
.
.
1
Primary DNS
Please input Primary DNS and press
[OK]. Press [CANCEL] to delete the selected
character. To clear this setting, delete all
characters and press [OK].
Num
ber
0 - 9
NOTE
Advanced operations
SC-BTX70EGEB-RQT9464-B.book 31 ページ ２００９年４月９日 木曜日 午後２時５３分
