23
RQT0A83
Firmware updates
Occasionally, Panasonic may release updated
firmware for this system that may add or improve the
way a feature operates. These updates are available
free of charge.
Preparation
≥
Turn this system on.
≥
Connect this system to the home network. (
l
7)
– Make sure that the network is connected to the
Internet.
1
Press [RADIO, EXT-IN]
repeatedly to select
“NETWORK”.
2
Press [SETUP] repeatedly to select “FW Update”
and then press [OK].
3
Press [
2
,
1
] to select “OK? Yes” and then press
[OK] to start the update.
≥
Select “OK? No” to cancel the update.
When the update begins, “Updating” is displayed.
The progress is displayed as “Upd
%” while
updating. (“
” stands for a number.)
4
After the update has finished, “Success” is
displayed.
Disconnect the AC mains lead and reconnect it
after 1 minute.
≥
If there are no updates, “No Need” is displayed.
≥
Downloading may take longer or may not work properly
depending on the connection environment.
Press [SETUP] repeatedly to select “FW Version” and
then press [OK].
The version of the installed firmware is displayed.
≥
Press [OK] to exit.
Others
As a factory default, this unit will turn to standby mode
automatically if there is no sound and it is not being
used for approximately 20 minutes.
To cancel this function
1
Press [SETUP] repeatedly to select “Auto Off”.
2
Press [
2
,
1
] to select “Off” and then press [OK].
≥
To turn the function on, select “On” in step 2.
≥
This setting cannot be selected when radio is the source or
when “Net Standby” is “On”.
≥
If “Net Standby” is set to “On”, this function will also be set to
“On”. To change the setting, set “Net Standby” to “Off”.
(
l
24)
≥
When connected to a Bluetooth
®
device, the function does
not work.
≥
When playing AllPlay, the function does not work.
When “SC-ALL7CD” is selected from a paired
Bluetooth
®
device’s Bluetooth
®
menu, this unit will turn
on automatically from standby mode and establish a
Bluetooth
®
connection.
1
Press [SETUP] repeatedly to select “BLUETOOTH
Standby”.
2
Press [
2
,
1
] to select “On” and then press [OK].
≥
To turn the function off, select “Off” in step 2.
≥
The factory default is “Off”. If this function is set to “On”, the
standby power consumption will increase.
When other Panasonic equipment responds to the
supplied remote control, change the remote control
code.
1
Press [CD/ ] repeatedly to select “CD”.
2
Press and hold [
∫
] on the unit and [2] on the
remote control until the unit’s display shows
“Remote 2”.
3
Press and hold [OK] and [2] on the remote control
for at least 4 seconds.
≥
To change the mode back to “Remote 1”, repeat the steps
above but replace [2] with [1].
You can also update the firmware from a pop-up
prompting you to do so on-screen within the app
“Panasonic Music Streaming” (version 3.1.0 or later)
(
l
10). For details on the app, refer to the site below.
http://panasonic.jp/support/global/cs/audio/app/
(This site is in English only.)
Downloading takes approx. 10 minutes.
DO NOT DISCONNECT the AC mains lead
while one of the following messages is
displayed.
“Updating” or “Upd
%”
(“
” stands for a number.)
≥
During the update process, no other operations can be
performed.
Checking the firmware version
Auto off function
Bluetooth
®
standby
Changing the unit and remote
control code
SC-ALL7CD_EGEBGN_RQT0A83-B.book 23 ページ ２０１６年３月１日 火曜日 午後４時１９分
