ENGLISH
RQTV0247
During FM stereo reception
On the main unit
1. Enter the menu.
Press
2. Select
“TUNER”
and confirm.
3. Select
“TUNE MODE”
and confirm.
4. Select
“PRESET”
and confirm.
5. Press [-MENU, –SETUP, RETURN] twice to select
“EXIT”
and press [ENTER].
6. Select the channel.
Press
During AM reception
Preset tuning
Presetting stations
Auto presetting
The FM stations the unit can receive are preset in channels
1 to 30. The AM stations the unit can receive are preset in
channels 21 to 30 (FM stations are replaced if any were
preset in these channels).
1. Tune to the frequency where you want to begin
(
➡
page 32).
Tune to FM 87.50 MHz or AM 522 kHz (9 kHz steps),
AM 530 kHz (10 kHz steps) to start from the lowest
frequency.
2. Enter the menu
Press
3. Select
“TUNER”
and confirm.
4. Select
“AUTO MEMO”
and confirm.
5. Select
“START”
and press [ENTER].
Select
“CANCEL”
to cancel.
During automatic presetting, the memory indicator (
)
flashes and the frequency scrolls. The memory indicator
and channel numbers are displayed for a second when
a station is preset.
The last station to be preset is played when presetting
finishes.
Stations may not preset correctly if broadcasts are too
strong or weak. Preset manually if this is the case.
•
•
•
Manual presetting
Preset the stations one at a time.
1. Tune to the station (
➡
page 32).
2. Enter the menu.
Press
3. Select
“TUNER”
and confirm.
4. Select
“MEMORY”
and confirm.
5. Select a channel number and press [ENTER].
“STORED”
is displayed.
6. Press [-MENU, –SETUP, RETURN] twice to select
“EXIT”
and press [ENTER].
To preset other channels, repeat from step 1.
•
Even if the AC mains lead is disconnected from the household mains socket, the stations remain in the memory for approximately two
weeks.
Selecting channels
On the remote control
Select the channel.
Press the numbered buttons to select the channel.
To select a two digit number
e.g. 21: [
≧
10, -/--]
→
[2]
→
[1]
•
•
Press and hold to change channels faster.
•
Select
“MANUAL”
in step 4 to tune manually again
(
➡
page 32).
Reducing excessive noise (on the main unit)
Preparation: Press [-MENU, –SETUP, RETURN] to enter the menu.
MENU
SETUP
RETURN
MENU
SETUP
RETURN
M
CH
0
-/--
MENU
SETUP
RETURN
TUNE
You can improve FM reception by switching reception to
monaural.
When there is a lot of noise interference with an AM broadcast,
try switching to this mode.
33
1. Select
“TUNER”
and confirm.
2. Select
“FM MODE”
and confirm.
3. Select
“MONO”
and confirm.
“MONO”
lights.
To return to normal reception, select
“AUTO”
.
4. Press [-MENU, –SETUP, RETURN] twice to select
“EXIT”
and press [ENTER].
•
•
1. Select
“TUNER”
and confirm.
2. Select
“BEAT PROOF”
and confirm.
3. Select
“MODE 1”
or
“MODE 2”
and confirm.
4. Press [-MENU, –SETUP, RETURN] twice to select
“EXIT”
and press [ENTER].
The radio
Preset channels to make selection simpler.
You can also preset FM stations in the MONO mode (
➡
below).
SA-XR59 (RQTV0247-B).indb 33
6/5/2007 9:11:36 AM
