Panasonic SA-VKX65, Руководство по эксплуатации

Страница: 30 / 32

30
RQT9951
Specifications
█
Amplifier section
RMS output power stereo mode
Front Ch 275 W per channel (3 ), 1 kHz
Total RMS stereo mode power 550 W (30% THD)
PMPO output power 6000 W
█
Tuner, terminals section
Preset station FM 30 stations
AM 15 stations
Frequency modulation (FM)
Frequency range
87.50 MHz to 108.00 MHz (50 kHz step)
Antenna terminals 75 (unbalanced)
Amplitude modulation (AM)
Frequency range
522 kHz to 1629 kHz (9 kHz step)
520 kHz to 1630 kHz (10 kHz step)
Mic jack
Terminal Mono, 6.3 mm jack (2 system)
Sensitivity 0.7 mV, 1.2 k
AUX 1
Audio input Pin jack (1 system)
AUX 2
Sensitivity 100 mV, 4.7 k
█
USB section
USB port
USB standard USB 2.0 full speed
Media file format support
USB AUDIO MP3 (
*
.mp3)
USB VIDEO JPEG (
*
.jpg,
*
.jpeg), Xvid (
*
.xvid,
*
.avi)
USB device file system FAT12, FAT16, FAT32
USB port power 500 mA (max)
Bit rate Up to 4 Mbps (Xvid)
USB recording
Bit rate 128 kbps
USB recording speed 1x
Recording file format MP3 (
*
.mp3)
█
Bluetooth ® section
Version Bluetooth ® Ver. 2.1 + EDR
Class Class 2
Supported profiles A2DP, AVRCP, SPP
Operating frequency 2.4 GHz band, FH-SS
Operation distance 10 m line of sight
█
HDMI progressive video
There is a ghosting effect when the HDMI progressive
output is on.
• This problem is caused by the editing method or
material used on DVD-Video, but should be corrected
if you use interlaced output. When using the HDMI
AV OUT terminal, set “VIDEO FORMAT” in Menu 4
to “480i” or “576i”. Or, disable the HDMI AV OUT
connection and use the other video connection.
(
Z
7, 16)
Remote control code
When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
Preparation
Press [RADIO/AUX] to select “AUX 1” or “AUX 2”.
█
To set the code to “REMOTE 2”
1
Press and hold [RADIO/AUX] on the main unit
and [2] on the remote control until “REMOTE 2”
is shown.
2
Press and hold [OK] and [2] for a minimum of
4 seconds.
█
To set the code to “REMOTE 1”
1
Press and hold [RADIO/AUX] on the main unit
and [1] on the remote control until “REMOTE 1” is
shown.
2
Press and hold [OK] and [1] for a minimum of
4 seconds.
Note:
After you set the code, you can continue to use the TV
operation buttons on the remote control to operate a
Panasonic TV (
Z
9).
System memory reset
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Disconnect the AC mains lead.
2
While you press and hold [
1
] on the main unit,
connect the AC mains lead again.
Continue to press and hold the button until
“– – – – – – – –” is shown.
3
Release [
1
].
All the settings are set back to the factory preset. It is
necessary to set the memory items again.
SC-VKX65GAGS_RQT9951-B_En.indd 30 SC-VKX65GAGS_RQT9951-B_En.indd 30 8/18/2014 3:31:36 PM 8/18/2014 3:31:36 PM
printing rev.1
Confidential
Until: 29 Aug 2014