4-115
VRF SYSTEMS Indoor Unit Specifications
1
2
3
4
5
6
7
8
9
7. High Static Pressure Ducted Type (Type E2)
4-114
1
2
3
4
5
6
7
8
9
7-6. Indoor Fan Performance
Item code
“
”
Setting at
shipment
Cooling
Heating
Cooling
Heating
Cooling
Heating
Tap
9
8
7
6
5
4
3
2
1
M
L
M
M
M
M
M
H
H
H
H
H
H
L
L
L
L
L
Type 224
0
20
40
60
80
100
120
140
160
180
200
220
240
260
280
300
320
20
40
60
80
100
120
140
160
180
200
220
240
260
280
300
320
35
40
45
50
55
60
65
70
5
3
1
9
7
4
8
6
2
L
M
H
L
M
H
L
M
H
(Pa)
External static pressure
External static pressure
Airflow Volume (m
3
/min.)
Airflow Volume (m
3
/min.)
Limit line
Limit line
Limit lin
e
Limit line
Limit line
Limit line
Type 224
100
120
140
160
180
200
220
240
260
280
300
320
15
20
25
30
35
40
(Pa)
External static pressure
Limit line
Limit line
Type 280
0
45
50
55
60
65
70
75
80
85
90
5
3
1
9
7
4
8
6
2
L
L
L
M
M
M
H
H
H
(Pa)
Airflow Volume (m
3
/min.)
Airflow Volume (m
3
/min.)
Limit line
Limit line
Limit line
Limit lin
e
Limit line
Limit line
Type 280
100
120
140
160
180
200
220
240
260
280
300
320
20
25
30
35
40
45
50
(Pa)
Ext
erna
l st
at
ic
pr
essu
re
Limit line
Limit line
In the case of Fresh Air Intake Mode
VRF SYSTEMS Indoor Unit Specifications
7. High Static Pressure Ducted Type (Type E2)
Type 180
(Pa)
30
35
40
45
50
55
60
140
160
180
200
220
240
260
280
300
320
60
40
20
100
120
80
0
H
H
H
M
M
M
L
L
L
9
7
4
8
6
2
3
1
5
Airflow Volume (m
3
/min.)
Exter
nal static pressure
Limit
lin
e
Limit line
Limit line
Limit lin
e
Limit line
Limit lin
e
Fig. 4-4
Fig. 4-3
4-115
VRF SYSTEMS Indoor Unit Specifications
1
2
3
4
5
6
7
8
9
7-7. External Static Pressure Setting
7. High Static Pressure Ducted Type (Type E2)
Choose one of the methods (selection of “a”, “b”, “c” within the range of dotted line as shown in the flowchart below)
and make settings.
a. No setting changes:
When using as it is factory preset at shipment.
(If resetting after external static pressure setting once, it might be different from factory preset.)
b. Manual setting (on PCB):
This is static pressure setting excepting factory preset at shipment. Dip switch select method.
c. Manual setting (by timer remote controller):
Static pressure setting excepting factory preset at shipment.
Flow of External Static Pressure
NOTE
(1) Refer to Table 4-6, 4-7, 4-8 and Fig. 4-3 for details on the relationship between the value of item code “5d” and
the external static pressure.
(2) When set in group control (connecting multiple indoor units with one timer remote controller), set each indoor
unit to item code “5d”.
When amending the setting after selecting [ b. Manual setting] (due to airflow path changes, etc.), it is
necessary to cancel [b. Manual setting] (switching OFF positions).
When [b. Manual setting] has not been cancelled, [c. Manual setting] will be activated if selected, but [b. Manual
setting] takes precedence when the power is switched back on after power outages, etc.
CAUTION
Make sure the external static pressure is in a range of specifications.
Then proceed the external static pressure setting.
Improper settings can cause noise, a shortage of airflow volume and water
leakage.
Refer to Fig. 4-3 for the external static pressure setting range.
Be sure to set the [External Static Pressure Setting] once again after amending
the airflow path for the duct or air outlet after setting the external static pressure.
Start of external static pressure setting
Setting of shipment : line
8
Is it designed and
installed at the setting line at
shipment on PQ line drawing?
Operating by
timer remote
controller
Selection methods
of external static
pressure setting
No
No
Yes
Yes
a. No setting changes
b. Manual setting
(Setting on PCB)
Setting switches of TP6 or
TP3 or TP1
Refer to section "7-7-1. How to
set on PC Board".
c. Manual setting
Item code 5d : Setting 1, 3, 6
(*Note 1) (*Note 2)
Refer to section 7-7-2, 7-7-3 or 7-7-4.
Completion of external static pressure setting
TD831172-03 VRF SYS INDOOR.indb 115
2015/06/04 12:06:55
