5. Do not use freon-propelled chemicals. These can generate
electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective
package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically
shorted together by conductive foam, aluminum foil or comparable
conductive material).
7. Immediately before removing the protective material from the
leads of a replacement ES device, touch the protective material to
the chassis or circuit assembly into which the device will be
installed.
CAUTION:
Be sure no power is applied to the chassis or circuit, and observe
all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement
ES devices. (Otherwise harmless motion such as the brushing
together of your clothes fabric or the lifting of your foot from a
carpeted floor can generate static electricity (ESD) sufficient to
damage an ES device).
"NOTE to CATV system installer :
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the
NEC that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of cable
entry as practical."
4. OPERATION GUIDE
5. SERVICE NOTES (PLEASE READ)
5.1. SERVICE NOTES
5.1.1. SIMPLIFIED FAULT FINDING DATA
Simplified Self-Diagnostic System facilitates finding the cause of the fault. A 4 digit for fault code
and communication for I
2
C bus code will be displayed on TV screen.
The Simplified Fault finding data is stored in the Memory IC (IC6004). This data is cleared after it
is displayed, and then the POWER button is pressed back on.
1. With power turned off, press FF and REW buttons on unit together
for over 3 seconds.
Fig. 1-1
8
Содержание PV-C1323A
