Panasonic PT53X54J - 53" PROJECTION TV HD, Руководство по обслуживанию

Страница: 6 / 213

http://tsn.pstc.panasonic.com/viewing/NA/PT-53X54J/SVC/s0100000000x.html
1 Safety precautions
TOP PREVIOUS NEXT
General guidelines
An isolation transformer should always be used during the servicing of a receiver whose chassis is not isolated from AC
power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in
personal injuryfrom electrical shocks. It will also protect the receiver from being damaged by accidental shorting that
may occur during servicing.
When servicing, observe the original lead dress, especially in the high voltage circuit. Replace all damaged parts (also parts
that show signs of overheating.)
Always replace protective devices, such as fish paper, isolation resistors and capacitors, and shields after servicing the
receiver. Use only manufacturers recommended rating for fuses, circuits breakers, etc.
High potentials are present when this receiver is operating. Operation of the receiver without the rear cover introduces
danger for electrical shock. Servicing should not be performed by anyone who is not thoroughly familiar with the
necessary precautionswhen servicing high voltage equipment.
Extreme care should be practiced when handling the picture tube. Rough handling may cause it to implode due to
atmospheric pressure. (14.7 lbs per sq. in.). Do not nick or scratch the glass or subject it to any undue pressure. When
handling, usesafety goggles and heavy gloves for protection. Discharge the picture tube by shorting the anode to chassis
ground (not to the cabinet or to other mounting hardware). When discharging connect cold ground (i.e. dag ground lead) to
the anode with a wellinsulated wire or use a grounding probe.Avoid prolonged exposure at close range to unshielded areas
of the picture tube to prevent exposure to x ray radiation.
The test picture tube used for servicing the chassis at the bench should incorporate safety glass and magnetic shielding.
The safety glass provide shielding for the tube viewing area against x ray radiation as well as implosion. The
magnetic shieldlimits the x ray radiation around the bell of the picture tube in addition to the restricting magnetic effects.
When using a picture tube test jig for service, ensure that the jig is capable of handling 50kV without causing x ray radiation.
Before returning a serviced receiver to the owner, the service technician must thoroughly test the unit to ensure that
is completely safe to operate. Do not use a line isolation transformer when testing.
Leakage current cold check
Unplug the A.C. cord and connect a jumper between the two plug prongs.Measure the resistance between the jumpered
AC plug and expose metallic parts such as screwheads, antenna terminals, control shafts, etc. If the exposed metallic part has
a returnpath to the chassis, the reading should be between 240k
Ω
and 5.2M
Ω
. If the exposed metallic part does not have
a return path to the chassis, the reading should be infinite.
Leakage current hot check
Plug the AC cord directly into the AC outlet. Do not use an isolation transformer during the check.
Connect a 1.5k
Ω
10 watt resistor in parallel with a 0.15
μ
F capacitor between an exposed metallic part and ground. Use
earth ground, for example a water pipe.
Using a DVM with a 1000 ohms/volt sensitivity or higher, measure the AC potential across the resistor.
Repeat the procedure and measure the voltage present with all other exposed metallic parts.
Verify that any potential does not exceed 0.75 volt RMS. A leakage current tester (such a Simpson model 229, Sencore
model PR57 or equivalent) may be used in the above procedure, in which case any current measure must not exceed
0.5 milliampere.If any measurement is out of the specified limits, there is a possibility of a shock hazard and the receiver
must be repaired and rechecked before it is returned to the customer.
Hot check circuit
http://tsn.pstc.panasonic.com/viewing/NA/PT-53X54J/SVC/s0100000000x.html (1 of 2) [23/04/2012 12:16:02 p.m.]