Panasonic PT-LX270U Скачать руководство пользователя

Страница: 3 / 62

Read this first!

ENGLISH -

Important

Information

FCC NOTICE (USA)

Declaration of Conformity

Model Number:

PT-LX300U / PT-LX270U

Trade Name:

Panasonic

Responsible Party: Panasonic Corporation of North America

Address:

One Panasonic Way, Secaucus, NJ 07094

Telephone number: (877)803-8492

E-mail: [email protected]

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

To assure continued compliance, follow the attached installation instructions and do not make any unauthorized

modifications.

CAUTION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one of the following measures:

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

•

The user may find the booklet “Something About Interference” available from FCC local regional offices helpful.

FCC Warning:

To assure continued FCC emission limit compliance, follow the attached installation instructions and the user

must use only shielded interface cables when connecting to host computer or peripheral devices. Also, any

unauthorized changes or modifications to this equipment could void the user’s authority to operate this device.

NOTIFICATION (Canada)

This class B digital apparatus complies with Canadian ICES-003.

WARNING:

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data

•

Processing Equipment, ANSI/NFPA 75.

For permanently connected equipment, a readily accessible disconnect device shall be incorporated in the

•

building installation wiring.

For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily

•

accessible.

Notice (USA only):

This product has a High Intensity Discharge (HID) lamp that contains mercury. Disposal may be regulated

•

in your community due to environmental considerations. For disposal or recycling information, please visit

Panasonic website: http://www.panasonic.com/environmental or call 1-888-769-0149.

Содержание PT-LX270U































































Результаты поиска

Содержание PT-LX270U

Отзывы:

Похожие инструкции для PT-LX270U

Бренды по названию

Популярные бренды

Panasonic PT-LX270U, Руководство по эксплуатации

Результаты поиска

Содержание PT-LX270U

Отзывы:

Похожие инструкции для PT-LX270U

Бренды по названию

Популярные бренды