Panasonic PT-52LCX66-K, Руководство по обслуживанию, Страница: 36 / 223

Check the voltage and waveform at Q1304-GATE.
(Use Radiation Plate for HOT circuit as GND.)
Refer to waveform in Figure 2.
Perform the REG9V Adjustment.
(Refer to "REG9V Adjustment" in Adjustment
Procedures 2.
NG
NG
NG
Plug in the AC Cord and turn the power ON.
Check if the voltage at TP1909 is 9.0 V±0.3V.
(Use bottom part of Radiation Plate for COLD circuit
as GND.)
Unplug the AC Cord.
Remove the jumper wire between TP1502 and TP1901
on the Power P.C.B., and reconnect all connector
cables, then reinstall the Power P.C.B. into the unit.
Check the voltage at the following points.
(Use CN1514 (Pin10-14) or bottom part of Radiation
Plate for COLD circuit as GND.)
OK
OK
Check the other parts on the Power P.C.B.
and replace any defective parts.
Perform "CHECKING THE BALLAST CIRCUIT."
Replace the Power P.C.B.
OK
Check if the voltage at Pin 8 of IC1831 is over DC15V.
(Use Radiation Plate for HOT circuit as GND.)
Check if the voltage at Pin 18 of CN1401 is over DC4V.
(Use TP1301 for COLD circuit as GND.)
NG
Check if the voltage at D1808-CATHODE is 400 V±5 V.
(Use Radiation Plate for HOT circuit as GND.)
OK
OK
NG
NG
Replace the Power Control 1 P.C.B.
Replace the Power Control 2 P.C.B.
OK
Check the voltage at the following points on the Power
Control 2 P.C.B.
(Use TP1301 as GND.)
CN1401 (Pin 6): approx. 0.5 V±0.5 V <SUB RELAY ON (L)>
CN1401 (Pin 7): approx. 0.5 V±0.5 V <MAIN RELAY ON (L)>
CN1401 (Pin 9): approx. 13.5V±1.5 V <STBY+12V>
NG
OK
A
B
C
OK
Do not touch any parts to reduce the risk of
electric shock after the AC Cord has been plugged
in even once. Before checking parts, confirm that
the voltage C1810 is 0V.
If not, discharge C1810 terminals by using a
resistor of 100 ohm/10 W or over for 3 seconds.
CAUTION:
Do not touch any parts to reduce the risk of
electric shock after the AC Cord has been plugged
in even once. Before checking parts, confirm that
the voltage C1810 is 0V.
If not, discharge C1810 terminals by using a
resistor of 100 ohm/10 W or over for 3 seconds.
CAUTION:
Do not touch any parts to reduce the risk of
electric shock after the AC Cord has been plugged
in even once. Before checking parts, confirm that
the voltage C1810 is 0V.
If not, discharge C1810 terminals by using a
resistor of 100 ohm/10 W or over for 3 seconds.
CAUTION:
Do not touch any parts to reduce the risk of
electric shock after the AC Cord has been plugged
in even once. Before checking parts, confirm that
the voltage C1810 is 0V.
If not, discharge C1810 terminals by using a
resistor of 100 ohm/10 W or over for 3 seconds.
CAUTION:
CN1514 (Pin1) or TP1908: approx. +7 V (STBY+7V)
CN1514 (Pin7) or TP1909: approx. +9 V (DT+9V)
CN1514 (Pin5) or TP1910: approx. +30 V (DT+30V)
CN1514 (Pin6) or TP1911: approx. +17 V (DRV+17V)
CN1516 (Pin2) or TP1914: approx. +18 V (AMP+18V)
TP1311 or D1404-ANODE: approx. +195 V (B)
PT-52LCX66-K / PT-56LCX16-K / PT-61LCX66-K
36