Panasonic PAW-VP1000LDHW Скачать руководство пользователя страница 24

Страница: 24 / 88

DHW PAW-VP - Installation manual – 2020-05

Water Piping Installation

General Notes

●

Please request a licensed technician to install this water circuit.

●

This water circuit must comply with all relevant European and national regulations,

i.e. IEC/EN 61770 European Council Directive 98/83 EC.

●

Be careful not to deform the piping with excessive force when doing piping connection

job.

●

When connecting pipes to tank, always use brass between pipe and tank sleeve to pre-

vent corrosion between base material.

●

Choose proper sealer which can withstand the pressures and temperatures of the sys-

tem. When tank is to be connected ensure the pipings are clean before water piping

installation is carried out.

●

Water operating pressures DHW tank (Minimum ~ Maximum): 0.05 MPa – 0.95 MPa

3.1 Tank Unit Refrigerant Piping Installation

Please make flare after inserting flare nut (located at joint portion of tube assembly) onto

the copper pipe. (In case of using long piping)

2. Do not use pipe wrench to open refrigerant piping. Flare nut may be broken and cause

leakage. Use proper spanner or ring wrench.

3. Connect the piping:

● Align the centre of piping and sufficiently tighten the flare nut with fingers.

● Further tighten the flare nut with torque wrench in specified torque as stated in the

table.

Model

Piping size (Braising tank)
Gas

Liquid

PAW-VP1000LDHW

3/4" [19.05 mm]

1/2" [12.7 mm]

PAW-VP750LDHW

3/4" [19.05 mm]

1/2" [12.7 mm]

PAW-VP380L

3/4" [19.05 mm]

1/2" [12.7 mm]

Nominal diameters of the junction pipes (refrigerant pipe diameter of the connecting pipe may

vary). Please refer to chapter 4 for Refrigerant connecting pipes.

Содержание PAW-VP1000LDHW

























































































Результаты поиска

Содержание PAW-VP1000LDHW

Отзывы:

Похожие инструкции для PAW-VP1000LDHW

Бренды по названию

Популярные бренды

Panasonic PAW-VP1000LDHW, Руководство по установке

Результаты поиска

Содержание PAW-VP1000LDHW

Отзывы:

Похожие инструкции для PAW-VP1000LDHW

Бренды по названию

Популярные бренды