background image

2

-

-

+

+

Warning and Important

Information

Notes:

– The service life of the batteries is approximately 1 year.

However, it varies considerably depending on the
frequency of use.

– When they are exhausted, replace them with two AA, UM3,

or R6 size batteries.

– When the batteries are exhausted, remove them

immediately and dispose of them correctly.

– Make sure that the batteries are inserted with the polarity

(

+

 and 

-

) correctly aligned.

– Do not mix old battery with new battery.
– Do not mix different battery types, i.e. Alkaline and

Manganese.

– Do not use rechargeable (Ni-Cd) batteries.
– Do not heat or short-circuit the batteries.
– When you do not use the remote control for a long time,

take out the batteries and store them in a cool, dry place.

Conserve the environment

See [Power save] of page 21.

Disposal of old equipment

Batteries, packaging and old equipment should not be
disposed of as domestic waste, but in accordance with the
applicable regulations.

Cautions before you operate this VCR

Avoid:
– Humidity and dust.
– Extreme heat such as direct sunlight.
– Magnets or electromagnetic objects.
– Touching internal parts of the VCR.
– Water or some other liquid.
– Lightning. (Disconnect the aerial plug from the VCR during

lightning storms.)

– Anything heavy on the VCR.
– Connecting or handling the equipment with wet hands.
– Using a cell phone near the VCR because doing so may

cause noise to adversely affect the picture and sound.

Do:
– Wipe the VCR with a clean and dry cloth.
– Install the VCR in a horizontal position.
– Keep the VCR, TV and other equipment switched off until

you have finished all connections.

Condensation may form in the following cases:

– The VCR is brought from cold surroundings into a

well-heated room.

– The VCR is suddenly brought from cool surroundings, such

as an air-conditioned room or car, to a place which is hot
and humid.

Note:

– In any of the above-mentioned conditions, do not operate

the VCR for at least 1 hour.
This VCR is not equipped with a dew sensor.

Standard Accessories
1 pc. RF Coaxial cable
1 pc. Remote Control (N2QAKB000001)
2 pcs. R6 size batteries
1 pc. AC mains lead

As this equipment gets hot during use, operate it
in a well ventilated place;
do not install this equipment in a confined space
such as a book case or similar unit.

Important

Your attention is drawn to the fact that the recording of
pre-recorded tapes or discs or other published or broadcast
material may infringe copyright laws.

Warning

To reduce the risk of fire or shock hazard, do not expose this
equipment to rain or moisture.

For your safety

Do not remove outer cover.
Touching internal parts of the VCR is dangerous, and may
seriously damage it.
To prevent electric shock, do not remove cover. There are no
user serviceable parts inside. Refer all servicing to qualified
service personnel.

Inserting Remote Control Batteries

Insert the batteries with the polarity (

+

 and 

-

) correctly

aligned.

Содержание NV-HS820 Series



























Отзывы: