Panasonic NR-C370GH-N3, Руководство по эксплуатации

Страница: 19 / 44

English
16
Appendix Appendix
Attention
In these cases ?
The power failed.
The power plug was
disconnected.
The refrigerator is not
used for a long time.
The automatic icemaker
is not used for a long time.
→ When starting to use
the automatic icemaker
again, switch on the
“AUTO ICE OFF” function.
When you move or
transport the refrigerator.
When you replace the
room lamp
●
Keep the doors closed and do not store additional food.
●「
QUICK FREEZING
」
stop. Reset these functions to use them after the power
recovery.
● Wait at least 7 minutes, and then plug in the power plug.
(If it is plugged in immediately, the compressor will be overloaded,
which may cause a malfunction.)
●
Remove all foods and drinks and clean the refrigerator.
①
Disconnect the power plug.
②
Clean the compartments and the ice-making tray. (P. 14 to P. 15)
③
Keep the doors opened for 2 to 3 days to dry the compartments.
(When drying is insufficient, the compartment may get moldy or have a foul smell.)
● Stop ice making, with the water supply tank empty, and clean the icemaker.
① Discard water in the water supply tank.
② Stop making ice. (P. 13)
③ Discard the stored ice in the ice-making tray and the ice storage box.
・ If ice cubes are left for long, they may become small or stick to each other.
④ Clean the upper case in the freezer compartment, the ice shovel, the water
supply tank and the ice-making tray with water. Dry them well and then put
them back to their position. The water purification filter in the water tank
contains water. Dry it properly.
● Do not transport refrigerators in a horizontal position.
(Doing so cause a failure of pipes around the compressor possible to be broken.)
● Remove the food and drinks in all compartments and discard the remaining
water and ice. Then, move the refrigerator with at least two people.
① Remove the food and drinks and discard water in the water supply tank.
② Stop the auto ice making function. (P. 13)
③ Clean the ice-making tray. (P. 15)
④ Remove the front grille screw in the adjustable legs.
(Remove the front grille before transporting the refrigerator.)
⑤ Disconnect the power plug.
⑥ Drain water from the evaporating pan.
・ Put a container not exceeding 3 cm tall
(with a volume of about 500 ml)
under the drain outlet, and take the stopper off (at the bottom on the back).
・ At first, break the film inside the drain outlet to let water out.
(From the next time, you only have to take the stopper off to let water out.)
・ After draining water, put the stopper back tightly
(for prevention of water leakage ） .
● If frost remains on the cooling unit (not visible from the outside) in
the refrigerator, then water may spill when it is moved.
(It takes approximately 15 hours for the frost on the cooling unit to melt after
the refrigerator power plug is disconnected.)
● When replace room lamp, please contact with your authorized dealer or
service center.
ECO NAVI Q&A
When does ECO NAVI
operate?
●
ECO NAVI by itself operates depending on the brightness around
the refrigerator, the change in the compartment temperatures, and the frequency of
door opening and closing. (ECO NAVI lamp lights up during ECO NAVI operation.)
The refrigerator compartment or freezer compartment door is open! (The “Notice” area then alternately indicates
“U” and ”10”.)
ECO NAVI lamp
does not light
（ ECO NAVI does not
operate ）
● ECO NAVI system operates only when the temperature of the refrigerator
compartment is set as "4 °C" or "5 °C" and the temperature of the freezer
compartment is set as "-19 °C", "-20 °C", or "-21 °C".
● If “U” or “H” is displayed on the notice indicator, ECO NAVI does not operate.
●
ECO NAVI does not operate until the refrigerator has been sufficiently cooled.
● ECO NAVI does not operate if you store hot food or you frequently open and
close the doors.
● The learning function may disable ECO NAVI operation in times of day when
the doors are frequently opened and closed, in order to cool the refrigerator well.
● If a power failure occurs, the collected learning function data will be lost.
ECO NAVI rarely operates until the learning function has collected sufficient data.
ECO NAVI lamp
does not turn off.
●
If the light intensity sensor (P. 11 ) is hidden or scratched,
the sensor may not work properly.
●
ECO NAVI may continuously operate even when the doors are opened and
closed, depending on the change in the compartment temperatures, while the
cooling performance is maintained.
ECO NAVI lamp turns
off when the doors are
not opened and closed.
● When (automatic) defrosting starts during ECO NAVI operation, for example, ECO
NAVI is stopped in order to perform normal cooling operation after the defrosting.
● The learning function may switch ECO NAVI operation back to normal cooling operation.
Bottom of the back
Drain outlet
If the following sounds or indications are generated
Double-
beep!
Display
1 minute later...Double-beep, 3 minutes later...Two double-beep,
5 minutes later...Continuous double-beeps
The letter “H” and a number are
alternately indicated on the “Notice”
indicator.
“Example”
An abnormality may have occurred.
If the indicator does appear,
contact your dealer.
19
Enfocus Software - Customer Support