Panasonic NN-GS595A Скачать руководство пользователя страница 27

Страница: 27 / 47

10/24/2016

XML Service Manual

file:///C:/Users/sh.dehghani/Desktop/NNGS595AOTSVC_PHAMOS0511035C3/viewing/SGML_VIEW_DATA/OT/NNGS595A/SVC/PHAMOS0511035C3/inde…

2/6

H02

Memory IC error (It is able to show up both in test mode and cooking mode)

H00

RAM failure (It is able to show up both in test mode and cooking mode)

H20

Steam heater open error

Usage problem

U14

No water during steam cooking (It is able to show up both in test mode and cooking mode)

U40

No load operation

U65

Power down controlled by magnetron thermistor

HOT

Oven is hot (It is able to show up both in test mode and cooking mode)

7.1 (Trouble) Oven stops operation during cooking

SYMPTOM

CAUSE

CORRECTIONS

SYMPTOM

CAUSE

CORRECTIONS

Oven stops in 3 seconds after
pressing start pad.

No input AC is supplied to H.V.Inverter (U) CN702
terminals

1. Latch Switch
2. Power relay RY1
3. Loose lead wire connector
CN701, CN702

Oven stops in 23 seconds after
pressing start pad.

H.V.Inverter (U) operates by the control signals from
DPC but magnetron is not oscillating

1. Magnetron
2. Loose lead wire connector
CN703

Oven stops in 1 minute after pressing
start pad. (Oven cooking)

Oven thermistor circuit is not functions.

1. Oven thermistor
2. Loose wiring

Oven stops in 30 seconds after
pressing start pad. (Steam cooking)

Steam heater thermistor circuit is not functions.

1. Steam heater thermistor
2. Loose wiring
3. bad conductibility between
thermistor and steam heater

No display and no operation at all.
Fuse is blown.

Most probably loose connection of connectors, or door
latch mechanism is not adjusted properly

1. Align door, Door Latch
Switches
2. Loose wiring connectors

7.2 (Trouble) Other troubles

SYMPTOM

CAUSE

CORRECTIONS

SYMPTOM

CAUSE

CORRECTIONS

Oven is dead.
Fuse is OK.
No display and no operation at
all.

1. Open or loose lead wire harness

Check fan motor if thermal cutout is
defective.

2. Open thermal cutout
3. Open low voltage transformer
4. Defective DPC
1. Shorted lead wire harness

Содержание NN-GS595A
















































Результаты поиска

Содержание NN-GS595A

Отзывы:

Похожие инструкции для NN-GS595A

Бренды по названию

Популярные бренды

Panasonic NN-GS595A, Руководство по обслуживанию

Результаты поиска

Содержание NN-GS595A

Отзывы:

Похожие инструкции для NN-GS595A

Бренды по названию

Популярные бренды