background image

- 18 -

8.2 The following symptoms are not trouble.

Symptoms

Time

Main Unit

Wash

Rinse / Spin

Remaining time fluctuates.

Checkpoints

• Remaining time is corrected during the process and displayed.
  (Time indication is an approximation.)

Cannot change the operation
contents. (after start)

• The contents can be changed in “Wash” process by pressing 
  “Pause”. To change the course or to change the contents after
  “Rinse” process, turn the power off and then turn on again.

The power is not turned on
immediately after power-off.

• Button operation is ignored approx. 10 seconds after power-off.

No water supply.

• Is the water faucet turned on?
• Is the lid closed?
• Water failure?
• Is the water supply filter clogged with dust?

No operation.

• Power failure?
• Is the lid closed completely?
• Is the power fuse or the breaker cut off?
• Is the power plug plugged in completely?
• Is the water faucet turned on?
• Is the “Start” button pressed?
• Has the “Reserve” program been set?

The water level is too high for
the amount of laundry.

• If the laundry is wet or if there is water in the tub before operation,
  the water level may be higher.

The water level is too low for
the amount of laundry.

• With light clothes (chemical fibre, etc.), the water level may be
  lower.

Irregular rotation during spin.

• The tub rotation speed is adjusted to reduce bubble foaming
  during spin.

Water is supplied in the middle
of Wash process.

• When level goes down, water is suppplied automatically.
• When large amount of laundry, water is supplied several times
  automatically.

The operation started with Rinse
process, however, water is not
supplied.

• If there is no water in the tub, water is supplied after spin.
• If there is water in the tub, water is supplied after water discharge.

The operation suddenly changes
to rinse process in the middle of
spin process. /
Only spin is desired, however,
the operation starts with rinse.

• If the laundry is unevenly placed in the tub, the machine starts to
  rinse and automatically corrects the arrangement.
  (Put the laundry as evenly as possible)

NA-F80B3 / F80H3 / F90B3 / F90H3 / F90G3 / 
F1003B / F1003H / F1103G / F100B3 / F100H3 / F100G3

Содержание NA-F1003B




































Отзывы: