42
43
When Necessary
Troubleshooting
(continued)
Symptoms
Check the following.
Rinse/Spin
Rinsing water is not
supplied.
If “Rinse” or “Rinse/Spin” is selected, the operation starts with water discharge if
water remains in the drum, and starts with spin if there is no water in the drum,
and then water is supplied.
During spin, the
operation changes
to “Rinse”.
If clothes are unevenly distributed, this may be automatically corrected, returning
to the “Rinse” cycle.
Spin is not
performed during
the “Spin” cycle.
The appliance detangles clothes for nice fi nish during the spin cycle.
When using the “Soak” or “ECONAVI (60 °C)” program for “Wash”, the fan operation is
performed in the middle of the spin cycle to remove moisture. This is not a malfunction.
Clothes are not wet
after washing.
In the following operation, thin fi bres, etc. may be dried when they are taken out
after washing.
• When operating the “Soak” or “ECONAVI (60 °C)” program for “Wash” (Moisture
is removed by fan operation)
Display
Washing time is
longer than the
displayed time.
If clothes are unevenly distributed, this is automatically corrected, leading to
longer operation time. This tends to occur especially when the amount of clothes
is too large or small.
Check the water drain hose and drain outlet. (P.45 “U11”)
In the following cases, excessive bubbles may be formed, and the operation time
may become longer to remove bubbles.
• Using large amount of detergent
• Using excessive foaming detergent
• Light soil on clothes
→Reduce the amount of detergent.
The total remaining
time diff ers from
the remaining time
of each process.
The “Soak” and “ECONAVI (60 °C)” programs detangle clothes for a slightly
longer time after the spin operation has fi nished.
Because of this, the total remaining time display may diff er from the remaining
time for the spin cycle displayed in the display window when the “Spin” button is
pressed.
Still operating
although the
remaining time
shows “0”.
After the drying operation has fi nished, the “Anti-crease” operation is performed
(approx. 2 hours) to prevent creases. (P.11)
The detergent
indication is
incorrect.
If water is in the drum, the indication may not be correct.
If clothes in the laundry net or wet clothes are in the drum, the indication may not
be correct due to balance of clothes.
→Load the laundry again (after detangling the clothes), and perform operation again.
The detergent amount
is not displayed.
For the “Bedding” and “Hand Wash” programs, the detergent amount is not
displayed because it is fi xed.
Check the following items before requesting service.
In the case of abnormality, contact the sales dealer immediately where you have purchased the appliance.
Symptoms
Check the following.
Main unit / Dry fi
lter
Button operation is
ignored.
After start, pressing “Pause” can change the settings for “Wash”, “Rinse” and
“Spin” until the end of the “Wash” cycle.
To change the program after start or change the settings after “Rinse”, turn the
power off and then back on.
Button operation is not possible if the door is open.
The door cannot
be opened.
Check the indicator in power “ON” state, and identify the cause.
•
illumination → The door is locked during operation.
•
illumi
display → Child Lock is set.
•
illumi
display → The door is locked if water temperature is
high.
•
illumination → The preset timer is being set.
→ To cancel the door lock (P.7)
Disturbing odour
The appliance (rubber or resin) may smell after purchase for certain period. This
smell will disappear as time passes using the appliance.
Take out the clothes immediately after the operation has fi nished.
Clean the back side of the window seal. (P.33)
Wash the drum. (P.32)
The dry fi lter is wet.
It may be wet after operation due to moisture formed during the washing or drying
operation. This is not a malfunction. Well dry. (Mould may form.)
The dry fi lter
moves.
The dry fi lter may move when the door is closed swiftly or during operation. This
is not a malfunction.
Water droplets
are attached on
the door, drum
or window seal
after the drying
operation.
In the following cases, water droplets may be attached due to the structure of the
door even if the clothes are dry. This is not a malfunction.
• The timer dry is used.
• Excessive clothes or many thick clothes are put in.
• The dry filter is clogged.
• The spin time is switched to shorter time.
→Wipe off water droplets.
