background image

5

3 Troubleshooting Guide

CONDITION

CHECKPOINT

METHOD OF INSPECTION

CAUSE / REMEDY

Motor fails to rotate

Power supply cord 

Check power supply cord continu-
ity.

If there is no continuity, replace the 
cord reel patition unit.

Fuse of P.C.B. Ass’y
(250V, 13A)

Check fuse continuity.

If there is no continuity, replace 
P.C.B. Ass’y.

Motor continuity

Check the conduction between the 
terminals of the motor.

If there is no continuity, replace the 
motor.

ON/OFF 

Switch

Check continuity across switch
connections

If there is no continuity, replace
P.C.B. Ass’y.

Triac (Inside of P.C.B.)

Check if there is any problem in the
triac.
(Please refer to how to check the
triac.)

If it has any problem, replace the 
P.C.B. Ass’y.

P.C.B. Ass’y

Check the internal parts for any-
thing unusual. (burn-out, melt-
down, etc.)

If anything unusual is found, 
replace the P.C.B. Ass’y with new 
one.

Motor runs but there is no suction Hose or Suction inlet

Check if there is any blockage in 
the hose or suction inlet.

If there is any blockage, remove it.

Dust box unit
Upper filter Unit
Secondary filter

Check whether or not the dust box 
unit is full of dust or dust is clogged 
in the upper filter unit or secondary 
filter.

If the dust box unit is full of dust, 
then throw away the dust.
If dust is clogged in the upper filter 
unit or secondary filter, then throw 
away the dust and clean or replace 
the upper filter unit or secondary fil-
ter.

Noise or vibration

Motor fan

Check dust accumulated in motor 
fan (it could happen if the vacuum 
cleaner has been used without cen-
tral filter).

If there is accumulated dust in the 
motor fan, replace the motor and 
check filter condition. (never try to 
dismantle the motor fan)

Motor does not change power 
(runs always at full speed)

P.C.B. Ass’y

Examine the triac in the P.C.B. 
Ass'y and check whether or not T1 
and T2 are short-circuited.

If they are short-circuited, then 
replace the P.C.B. Ass'y.

Motor runs irregularly

P.C.B. Ass’y

Check possible bad contact of 
P.C.B. Ass’y.

Replace P.C.B. Ass’y.

Содержание MC-CL671-RA76














Отзывы: