background image

5

3 Troubleshooting Guide

CONDITION

CHECKPOINT

METHOD OF INSPECTION

CAUSE / REMEDY

Motor fails to rotate

Power supply cord 

Check power supply cord continu-
ity.

If there is no continuity, replace the 
cord reel patition unit.

Fuse of P.C.B. Ass’y
(250V, 13A)

Check fuse continuity.

If there is no continuity, replace 
P.C.B. Ass’y.

Motor continuity

Check the conduction between the 
terminals of the motor.

If there is no continuity, replace the 
motor.

ON/OFF 

Switch

Check continuity across switch
connections

If there is no continuity, replace
P.C.B. Ass’y.

Triac (Inside of P.C.B.)

Check if there is any problem in the
triac.
(Please refer to how to check the
triac.)

If it has any problem, replace the 
P.C.B. Ass’y.

P.C.B. Ass’y

Check the internal parts for any-
thing unusual. (burn-out, melt-
down, etc.)

If anything unusual is found, 
replace the P.C.B. Ass’y with new 
one.

Motor runs but there is no suction Hose or Suction inlet

Check if there is any blockage in 
the hose or suction inlet.

If there is any blockage, remove it.

Dust bag / Secondary filter

Check if dust bag is full or Second-
ary filter is choked up.

If dust bag is full, replace with a 
new one. If Secondary filter is 
choked up, remove and clean it out 
or replace.

Noise or vibration

Motor fan

Check dust accumulated in motor 
fan (it could happen if the vacuum 
cleaner has been used without cen-
tral filter).

If there is accumulated dust in the 
motor fan, replace the motor and 
check filter condition. (never try to 
dismantle the motor fan)

Motor does not change power 
(runs always at full speed)

Power control

Adjust the power control and check 
whether or not the resistance var-
ies. (Gray

←→

Blue)

If the resistance does not vary, then 
replace the P.C.B. Ass'y.

P.C.B. Ass’y

Examine the triac in the P.C.B. 
Ass'y and check whether or not T1 
and T2 are short-circuited.

If they are short-circuited, then 
replace the P.C.B. Ass'y.

Motor runs irregularly

P.C.B. Ass’y

Check possible bad contact of 
P.C.B. Ass’y.

Replace P.C.B. Ass’y.

Содержание MC-CG476-JE7A












Отзывы: