Panasonic LUMIX DMC-GM1KP Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 60

Panasonic LUMIX DMC-GM1KP Скачать руководство пользователя страница 37

37

8.4.

Service Position

This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.

Table S1 Extension Cable List

CAUTION. (When servicing Main P.C.B.)

1. Be sure to discharge the E.Capacitor on Main P.C.B..

Refer to “How to Discharge the E.Capacitor on Main P.C.B.”.
The E.Capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed.

2. Be careful of the high voltage circuit on Main P.C.B..
3. DO NOT allow other parts to touch the high voltage circuit on Main P.C.B..

No.

Parts No.

Connection

From

1

RFKZ0487

FP9002 (MAIN)

←→

MAIN-TOP FPC - FP8001 (TOP)

35pin / 0.3 FFC

2

VFK1173

FP9003 (MAIN)

←→

REAR OPERATION UNIT

14pin / 0.5 FFC

3

RFKZ0631

FP9001 (MAIN)

←→

FRONT-MOUNT UNIT

16pin / 0.4 FFC

4

RFKZ0619

FP9006 (MAIN)

←→

LCD UNIT

61pin / 0.3 FFC

5

VFK1173

FP9005 (MAIN)

←→

FRONT-MOUNT UNIT

14pin / 0.5 FFC

«
...
35
36
37
38
39
...
»

Содержание LUMIX DMC-GM1KP





























































Отзывы:

Нет отзывов