Panasonic Lumix DMC-FT20EB, Руководство по обслуживанию

Страница: 24 / 90

24
1) About "*" indication:
The third digit from the left is different as follows.
In case of 0 (example: 18
0 01000)
When the third digit from the left shows "0", this error occurred under the condition of INITIAL SETTINGS has been completed.
It means that this error is occurred basically at user side.
In case of 8 (example: 18
8 01000)
When the third digit from the left shows "8", this error occurred under the condition of INITIAL SETTINGS has been released.
(Example; Factory assembling-line before unit shipment, Service mode etc.)
It means that this error is occurred at service side.
2) About "?" indication: ("18*0 0?01" to "18*0 0?50"):
The third digit from the right shows one of the hexadecimal ("0" to "F") character.
HARD VENUS A/
D Flash 28*0 0000 Flash charging error. STRB CHG FLASH P.C.B./
FPC
IC6001-(AC16) signal line or Flash charging circuit
FLASH
ROM
(EEPROM
Area) FLASH
ROM
(EEPROM
Area) 2B*0 0001
0003
0004 EEPROM read error FROM RE FROM
IC6002 (FLASH ROM)
0002 EEPROM write error FROM WR FROM
IC6002 (FLASH ROM)
0005 Firmware version up error (No indication) (No indication)
Replace the firmware file in the SD memory card.
0008 SDRAM error
0009 SDRAM Mounting defective
SYSTEM RTC 2C*0 0001 SYSTEM IC initialize failure error SYS INIT MAIN P.C.B.
Communication between IC6001 (VENUS ENGINE)
and IC9101 (SYSTEM)
SOFT CPU Reset 30*0 0001
|
0007
NMI reset
Non Mask-able Interrupt
(30000001-30000007 are caused by factors) NMI RST MAIN P.C.B.
Card Card 31*0 0001 Card logic error SD CARD SD CARD/
DSP
SD memory card data line or IC6001 (VENUS
ENGINE)
0002 Card physical error
SD memory card data line or IC6001 (VENUS
ENGINE)
0004 Write error SD WRITE
SD memory card data line or IC6001 (VENUS
ENGINE)
39*0 0005 Format error INMEMORY FROM
CPU,
ASIC hard Stop 38*0 0001 Camera task finish process time out. LENS COM LENSu/DSP
Communication between Lens system and IC6001
(VENUS ENGINE)
0002 Camera task invalid code error. DSP DSP
IC6001 (VENUS ENGINE)
0100 File time out error in recording motion image
IC6001 (VENUS ENGINE)
0200 File data cue send error in recording motion image
IC6001 (VENUS ENGINE)
0300 Single or burst recording brake time out.
Memory
area 3A*0 0008 USB work area partitioning failure (No indication) (No indication)
USB dynamic memory securing failure when
connecting
Operation Power on 3B*0 0000 FLASHROM processing early period of camera
during movement. INIT (No indication)
Zoom Zoom 3C*0 0000 Imperfect zoom lens processing ZOOM ZOOMm/
LENSu
Zoom lens
35*0 0000
|
FFFF
Software error
(0-7bit : command, 8-15bit : status) DSP DSP
35*1 0000 Though record preprocessing is necessary, it is not
called.
35*2 0000 Though record preprocessing is necessary, it is not
completed. (No indication) (No indication)
Attribute Main item Sub item Error code Contents (Upper) Error Indication
High 4bits Low 4 bits Check point (Lower) Detecting
device
Part/Circuit