background image

LC2H

Changing the preset value

Compliance with the CE marking

5. Output setting mode

This sets the operation mode.

1) Pressing the SET key four times while 
holding down the MODE key takes you to 
the output setting mode.
2) The display reads “HoLd-A” (initial 
setting) after entering the output setting 
mode.

3) Pressing the setting key causes the 
display to change as follows:
HOLD-B (Output maintain/over count I)

SHOT-A (One shot/over count)

SHOT-B (One shot/recount I)

HOLD-A (Output maintain/hold count)
4) Pressing the front panel reset key sets 
the display content and returns you to 
regular operation mode.

Note: You will not be returned to regular operation 

mode if you do not press the front panel reset 
key.

HOLD-A

HOLD-B

SHOT-B

SHOT-A

Press the SET key while pressing

the MODE key.

+

Un-Lock

Lock

Press the SET key while pressing

the MODE key.

+

Mode changes as follows by pressing the SET key while holding down the MODE key.

When the lock is set, you cannot enter modes other than 
backlight setting mode.

Lit red

Flashes green

Lit green

Flashes red

Press the SET key while pressing

the MODE key.

+

Addition

Subtraction

Press the SET key while pressing

the MODE key.

+

HOLD-A

HOLD-B

SHOT-B

SHOT-A

Lock mode

Backlight setting mode

Output setting mode

Input setting mode

Press the SET key while pressing

the MODE key.

+

2) Lock mode

3) Backlight setting mode

4) Input setting mode

5) Output setting mode

Front panel reset key

Regular operation mode

Please be aware that after doing a front 
panel reset key and returning to regular 
operation mode, the preset values, count 
value and output will be as shown in this 
table.

Note: “

×

” sign: No change

Preset 

value

Count value

Output 

change

Lock 
mode

×

×

×

Backlight 
setting 
mode

×

×

×

Input 
setting 
mode

×

Addition: “0”
Subtraction: 
“Preset value”

ON

OFF

Output 
setting 
mode

×

Addition: “0”
Subtraction: 
“Preset value”

ON

OFF

1. It is possible to change the preset 
value even during counting. However, 
be aware of the following points.

1) If the preset value is changed to less 
than the count value with counting set to 
the addition direction, counting will 
continue until it reaches full scale, returns 
to zero, and then reaches the new preset 
value. If the preset value is changed to a 
value above the count value, counting will 
continue until the count value reaches the 
new preset value.

2) Suppose that the counter is preset to 
count down. Whether a preset count 
down value is smaller or larger than the 
count value, the counter counts down to 
“0 (zero)”.

2. If the preset value is changed to “0”, 
the counter will not complete count-
up. It starts counting up when the 
counting value comes to “0 (zero)” 
again.

1) Addition (up-count) input when 
counting is set to the addition direction, 
counting will continue until full scale is 
reached, return to zero, and then 
complete count-up.
2) Subtraction (down-count) input when 
counting is set to the subtraction direction, 
counting will continue until full scale 
“–9999999” is reached, and then the 
display will change to “

”.

• EMC Directive (89/336/EEC)
The LC2H Preset Counter conforms to 
the EMC Directive as a simple counter.
Applicable standards: EN61000-6-4, 
EN61000-6-2

CTi Automation - Phone: 800.894.0412 - Fax: 208.368.0415 - Web: www.ctiautomation.net - Email: [email protected]

Содержание LC2H preset



































Отзывы: