1
Getting Started
Section 1
1-A Accessories
1-B Location of Controls
1-C Settings
∑
AC Adaptor . . . . . . . . . . . . . . . . . one
∑
Order No.
PQLV19Z
(PQLV19)
∑
Telephone Line Cord . . . . . . . . . one
∑
Order No.
PQJA10075Z
∑
Battery . . . . . . . . . . . . . . . . . . . . one
∑
Order No.
N4HHEPA00001
(HHR-P513)
∑
Handset Cover . . . . . . . . . . . . . . one
∑
Order No.
PQKK10136Z2 (Black)
PQKK10136Z1 (White)
∑
Belt Clip . . . . . . . . . . . . . . . . . . . one
∑
Order No.
PQKE10361Z2 (Black)
PQKE10361Z1 (White)
∑
Shoulder Rest Attachment . . . . . one
∑
Order No.
PQKE10364Z1
≥
For extra orders, call 1-800-332-5368.
3
Charge the battery for about 6 hours.
≥
See section 4-A for more
details.
≥
The CHARGE indicator
lights and the unit beeps
once.
≥
It is normal for the back
on the handset to feel
warm during battery
charge.
Handset
Base unit
≥
USE ONLY WITH Panasonic AC ADAPTOR PQLV19 (Order No.
PQLV19Z).
≥
The AC adaptor must remain connected at all times. (It is normal
for the adaptor to feel warm during use.)
≥
The unit will not work during a power failure. To connect a standard
telephone on the same line, use the Panasonic T-adaptor KX-J66.
To select the dialing mode TONE (preset) or PULSE
You can program the dialing mode
using the handset near the
base unit
.
Make sure the unit is not being used and the
handset is lifted off the base unit before programming.
While pressing
[FLASH/CALL WAIT]
:
Press and hold
[#]
(PULSE) until the unit beeps.
OR
Press and hold
[ ]
(TONE) until the unit beeps.
≥
If 3 beeps sound during programming, walk closer to the base
unit and start again from the beginning.
STOP
1
Connect as shown.
Power Outlet
(AC 120 V, 60 Hz)
AC
Adaptor
Telephone
Line Cord
Single-Line Telephone Jack (RJ11C)
Fasten the AC
adaptor cord.
Hooks
CHARGE Indicator (1-C)
[HANDSET LOCATOR]
(3-B)
Charge
Contacts (4-A)
IN USE Indicator (2-B, 3-B)
Antenna (4-F)
[SP-PHONE]
(Speakerphone/
Channel) (2-A)
[ ]
(TALK/Channel) (2-A)
[REDIAL]
(2-A)
[OFF]
(2-A)
VOL.
(VOLUME) Key
(
[
▲
]
,
[
▼
]
) (2-A, 2-B)
[VOICE ENHANCER]
and Indicator (2-A)
Talk/Ringer Indicator
(2-A, 2-B)
Microphone (2-A)
RECHARGE
Indicator (4-A)
Receiver
Headset Jack (4-D)
[FLASH/CALL WAIT]
(3-D)
Antenna
Charge Contacts (4-A)
Speaker
Back side
Ringer
Indicator (2-B)
[ ]
(TONE) (3-C)
2
Insert the battery (
1
), and press it down until it
snaps into the compartment (
2
).
Close the cover.
1
2
For assistance, please call: 1-800-211-PANA(7262)
CHARGE indicator
OR
To replace the battery:
Press the notch on the cover firmly and
slide it as indicated by the arrow.
Replace the old battery with a new one
(4-A). Close the cover and charge the
battery for about 6 hours.
PQQX13574XA 6/13/03 3:46 PM ページ 1
