Making Connection Mode
Settings
1.
Select
"Connection mode"
and press
[ENTER]
.
•
The connection mode setting screen is
displayed.
2.
Press
[ENTER]
, use
[
][
]
to select the desired
connection mode, and then press
[ENTER]
again.
"IP Mode"
: Communication is established over the
Internet or an intranet.
"NAT Traversal Mode"
: Communication is
established using KX-VC Series NAT Traversal
Service.
"IP / NAT Traversal Mode"
: Performs
communication using the 2 modes of IP Mode and
NAT Traversal Mode.
Note
•
Communication cannot be established with
a party whose connection mode setting
differs from yours.
•
"NAT Traversal Mode"
can be used only
after activating KX-VC Series NAT
Traversal Service with an activation key.
For details about KX-VC Series NAT
Traversal Service, refer to the following web
site:
http://panasonic.net/psn/products/hdvc/
nat_traversal/index.html
3.
Press
[G]
.
•
A dialogue box to confirm the saving of settings
and system restart after saving is displayed.
4.
Use
[
][
]
to select
"Yes"
and press
[ENTER]
.
•
The system will automatically restart to reflect
changes to system settings.
Note
•
When changing the connection mode, the time
required for a restart may depend on network
conditions.
Making NAT Settings
Note
•
To change the static NAT settings, it is
necessary to configure system settings,
including the port number settings. For details,
contact your dealer.
•
When using IP mode (Page 122),
"NAT"
is not
displayed in step
.
•
When using NAT traversal mode (Page 122),
"Static NAT"
,
"WAN IP Address"
, and
"Local
address judgement"
are not displayed in step
.
•
This setting is available only when
"IP Address
(LAN 1)"
(setting) is set to
"Manual"
in
"Network Settings"
1.
Select
"NAT Settings"
and press
[ENTER]
.
•
The NAT settings screen is displayed.
2.
Use
[
][
]
to select the following items for input:
•
The following items are displayed over 2 pages.
To view all the items, press
[R]
to move to the
next page, and press
[B]
to move to the
previous page.
•
If the settings have been changed, press
[G]
before changing to a different screen to save
the settings.
"NAT"
: Press
[ENTER]
and use
[
][
]
to select
"Dynamic"
(default) or
"Static"
.
"Static NAT"
: Use
[
][
]
to select
"ON"
or
"OFF"
(default).
Note
•
To select
"ON"
,
"H.460"
must be set to
"OFF"
on the H.323 settings screen
•
When
"ON"
is selected, the IP address of
the WAN side will be displayed for the unit
information on the Home screen (Page 38).
"WAN IP Address"
: Enter the WAN IP address of
the router.
Note
•
IPv6 addresses cannot be used for setting.
•
If the IP address contains 1 or 2 digit
numbers, enter these numbers as they are.
Do not enter like [.001].
Example: The IP address is [192.168.0.1].
–
Correct entry: [192.168.0.1]
–
Wrong entry: [192.168.000.001]
•
If
"Obtain automatically"
is displayed, the
WAN IP address cannot be set. For details,
contact your dealer.
"Local address judgement"
: Press
[ENTER]
and
use
[
][
]
to select
"OFF"
(default) or
"Auto"
.
–
"OFF"
(default): Static NAT is applied to all
addresses.
–
"Auto"
: Static NAT is not applied to private
addresses.
122
User Manual
Document Version 2015-08
Contacts and Settings
