manualshive.com logo in svg

Panasonic KX-TS600CB, Руководство по эксплуатации

Поделиться
Скачать
Panasonic KX-TS600CB Скачать руководство пользователя страница 52

52

CAUTION:

To reduce the risk of fire or injury to persons, read and follow these instructions.

1. Use only the battery(ies) specified.
2. Do not dispose of the battery(ies) in a fire. It (they) may explode.
3. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and 

may cause burns or injury to the eyes or skin. The electrolyte may be toxic if 
swallowed.

4. Exercise care in handling the battery(ies) in order not to short the battery(ies). 

Avoid contact with conductive materials such as rings, bracelets, and keys. The 
battery(ies) and/or conductor may overheat and cause burns.

5. Do not recharge the battery(ies) provided with or identified for use with this 

product. The battery(ies) may leak corrosive electrolyte or explode.

6. Do not attempt to rejuvenate the battery(ies) provided with or identified for use 

with this product by heating. Sudden release of battery electrolyte may occur 
causing burns or irritation to the eyes or skin.

7. Replace all batteries at the same time. Mixing fresh and discharged batteries 

could increase internal cell pressure and rupture the discharged batteries. 
(Applies to products employing more than one separately replaceable primary 
battery.)

8. When installing batteries observe the proper polarity or direction. Incorrect 

installation can cause charging, and may result in leakage or explosion. 
(Applies to products employing more than one separately replaceable primary 
battery.)

9. Remove the battery(ies) from this product if the product will not be used for a 

long period of time (several months or more). During this time the battery(ies) 
could leak in the product.

10. Discard the dead battery(ies) as soon as possible. The dead battery(ies) may 

leak in the product.

11. Do not store this product, or the battery(ies) provided with or identified for use 

with this product, in high temperature areas. Batteries that are stored in a 
freezer or refrigerator for the purpose of extending shelf life should be 
protected from condensation during storage and defrosting. Batteries should 
be stabilized at room temperature prior to use after cold storage.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS 
PRODUCT TO RAIN OR ANY TYPE OF MOISTURE.

If there is any trouble, disconnect the unit from the telephone line and 
connect a known working phone. If the known working phone operates 
properly, do not reconnect the unit to the telephone line until the trouble has 
been repaired. If the known working phone does not operate properly, 
consult your telephone company.

Important Safety Instructions

TS600CW_B02.book  Page 52  Tuesday, January 24, 2006  10:57 AM

Содержание KX-TS600CB

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды