Panasonic KX-TPA73 Скачать руководство пользователя страница 155

Страница: 155 / 161

Problem

Possible Cause

Solution

You cannot make/
receive a call.

The handset is out of
range, or the base unit is
busy.

Move closer to the base unit
or try again later.

The radio channel is busy,
or a radio communication
error occurred.

Try again later.

The handset is not
registered to the base unit.

Register the handset to the
base unit. For details, see
9.4 Registering/
Deregistering a Handset/
Desk Phone to the
Panasonic base unit, page
117.

You cannot dial.

The number that you
dialed is restricted by your
phone system.

Consult your administrator
or your phone system
dealer/service provider.

Key lock mode is on.

To cancel the mode, press
and hold

for about 2

seconds.
For details, see 2.9 Key
Lock, page 54.

The radio channel is busy
or a radio communication
error occurred.

Try again later.

The handset stops
working during
operation.

An unknown error has
occurred.

• Turn the handset off, and

then turn it back on.
For details, see
2.12 Power On/Off
(KX-TPA70/KX-TPA73
only), page 57.

• Re-insert the battery and

try again.
For details, see
9.2.1 Battery Installation,
page 113.

10.1.9 Troubleshooting

155

Содержание KX-TPA73


































































































































































Результаты поиска

Содержание KX-TPA73

Отзывы:

Похожие инструкции для KX-TPA73

Бренды по названию

Популярные бренды

Panasonic KX-TPA73, Руководство по эксплуатации

Результаты поиска

Содержание KX-TPA73

Отзывы:

Похожие инструкции для KX-TPA73

Бренды по названию

Популярные бренды