58
KX-TGE210/KX-TGE212/KX-TGE232/KX-TGE233/KX-TGE234/TGEA20
12.5. Things to Do after Replacing IC or X'tal
If repairing or replacing EEPROM and X'tal, it is necessary to download the required data such as Programming data or adjustment
data, etc. in memory.
The set doesn't operate if it is not executed.
12.5.1. How to download the data
12.5.1.1. Base Unit
First, operate the PC setting according to
Then download the appropriate data according to the following procedures.
Note:
(*1) WW: model number, XXX_YYY: revision number, ZZZ:Voice prompt, AA: Baud rate(9600/19200/57600/115200)
"XXX_YYY” and
"ZZZ" vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in
12.5.1.2. Handset
First, operate the PC setting according to
Then download the appropriate data according to the following procedures.
Note:
(*2) XXX_YYY: revision number
"XXX_YYY" vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in
Items
How to download/Required adjustment
BBIC(IC501)
Programming data is stored in memory.
1) System Clock adjustment.
EEPROM (IC611)
Adjusted parameter data is stored in memory.
(country version batch file, default batch file,
etc.)
1) Change the address “0001” of EEPROM to “AA” to download
the data.
2) Default batch file: Execute the command “default.bat”.
3) Country version batch file: Execute the command
“TG49WW_US_US_RevXXX_YYY.bat”. (*1)
4) System Clock adjustment
X'tal (X1)
System clock
Clock adjustment data is in EEPROM, adjust the data again
after replacing it.
1) Apply 5.5V between DCP ad DCM with DC power.
2) Input Command "sendchar sfr", then you can confirm the
current value.
3) Check X'tal Frequency.(10.368MHz ± 41Hz).
4) If the frequency is not 10.368MHz ±41Hz, adjust the
frequency of CLK executing the command "sendchar sfr xx xx
(where xx is the value)" so that the reading of the frequency
counter is 10.368MHz ±5Hz.
Items
How to download/Required adjustment
BBIC(IC1)
Programming data is stored in memory.
1) System Clock adjustment.
EEPROM (IC3)
Adjusted parameter data is stored in memory.
(country version batch file, default batch file,
etc.)
1) Default batch file: Execute the command “default.bat”.
2) Default batch file (remaining): Execute the command
“TGEA20_US_DEF_RevXXX_YYY.bat”. (*2)
3) Country version batch file: Execute the command
“TGEA20_US_US_RevXXX_YYY.bat”. (*2)
4) System Clock adjustment
5) 2.35 V setting and battery low detection
X'tal (X1)
System clock
1) Apply 2.6V between BATT+ and BATT- with DC power.
2) Input Command " sendchar sfr", then you can confirm the
current value.
3) Check X'tal Frequency.(13.824 MHz ± 100 Hz).
4) If the frequency is not 13.824 MHz ± 100 Hz, adjust the fre-
quency of CLK executing the command "sendchar sfr xx xx
(where xx is the value)" so that the reading of the frequency
counter is 13.824000 MHz ± 5 Hz.
Содержание KX-TGEA20B
Страница 65: ...65 KX TGE210 KX TGE212 KX TGE232 KX TGE233 KX TGE234 TGEA20 Memo ...
Страница 72: ...72 KX TGE210 KX TGE212 KX TGE232 KX TGE233 KX TGE234 TGEA20 Memo ...
Страница 75: ...75 KX TGE210 KX TGE212 KX TGE232 KX TGE233 KX TGE234 TGEA20 Memo ...
Страница 79: ...79 KX TGE210 KX TGE212 KX TGE232 KX TGE233 KX TGE234 TGEA20 Memo ...
