Panasonic KX-TG2220BXB Скачать руководство пользователя страница 39

Страница: 39 / 86

12.3. X201 Check

The confirmation is made under the “TX Power Check” mode of TEST MODE.

Equipment: Frequency counter

TP for measurement: TP_ANT

Measure range: 2472.64550 MHz ± 5 kHz (1ch) at Test Standby mode in TEST MODE (P.37).

12.4. Adjustment Battery Low Detector Voltage

After replacing handset’s DSP (IC201), Re-writing Battery Low voltage to EEPROM is required.

1. Set 2.7V for DC power supply.

2. Enter the test mode (Refer to Test mode flow chart for Handset (P.38))

3. Follow to “Batt Low Check” mode......... (Slave TDD is displayed on LCD)

4. Set 2.37V for DC power supply.

Note: Check voltage at battery connector, because some voltage drop is happened, using long or thin cable.

5. Press “#“ key to write voltage value in EEPROM.

6. Turn power off. Then this value is available.

KX-TG2220BXB / KX-TG2220B XF / KX-TG2220B XS / KX-TGA226BXB / KX-TGA226BXF / KX-TGA226BXS

Содержание KX-TG2220BXB























































































Результаты поиска

Содержание KX-TG2220BXB

Отзывы:

Panasonic KX-TG2220BXB, Руководство по обслуживанию, Страница: 39 / 86

Результаты поиска

Содержание KX-TG2220BXB

Отзывы: