place. The monitored handset (placed in a baby’s
room, for example) will automatically call the
monitoring handset, base unit, or the phone
number stored when it detects sound.
Important:
R
You should perform a test run of the baby
monitor procedure to ensure that the baby
monitor feature is set correctly. For example,
test its sensitivity. Check the connection if you
are diverting the baby monitor to an outside line.
R
This feature should not be used as a substitute
for a medical or caregiver’s supervision. It is the
caregiver’s responsibility to stay close enough
to handle any eventuality.
Note:
R
If the unit is connected to a PBX system, you
cannot set the baby monitor.
R
During the monitoring mode, battery
consumption is faster than usual. We
recommend leaving the monitored handset on
charger.
R
The monitored handset never rings while it is
being monitored. If the base unit is placed near
the monitored handset, we recommend turning
off the base unit ringer volume (page 29).
Setting the baby monitor
Perform the setting operation with the handset to
be monitored (for example, the handset placed in
a baby’s room).
To monitor with a unit
The internal baby monitor feature is available:
– between handsets
– between a handset and the base unit
Handset
1
M
MENU
N#268
2
MbN
:
“
On
”
a
M
SELECT
N
3
MbN
: Select the desired unit’s number to
monitor with.
a
M
SAVE
N
R
“
Baby monitor
”
will be displayed.
R
The registered unit’s name/number is
displayed.
Note:
R
When this feature is on, another handset or the
base unit can hear the monitored handset by
making an intercom call.
To monitor from an outside line
If you enable this feature, the unit will call a
pre-programmed phone number when the handset
detects sound. After you answer the call, you can
listen in on the room where the handset is located.
Handset
n
From the phonebook:
1
M
MENU
N#268
2
MbN
:
“
On
”
a
M
SELECT
N
3
MbN
: Select
“
Outgoing call
”
to monitor
from an outside line.
a
M
EDIT
N
a
M
ADD
N
4
MbN
:
“
Phonebook
”
a
M
SELECT
N
5
MbN
: Select the phonebook entry.
a
M
SAVE
N
R
“
Baby monitor
”
will be displayed.
Note:
R
If you edit a phonebook entry which is assigned
for monitoring, the edited entry does not transfer
to the monitor.
n
By entering phone numbers:
1
M
MENU
N#268
2
MbN
:
“
On
”
a
M
SELECT
N
3
MbN
: Select
“
Outgoing call
”
to monitor
from an outside line.
a
M
EDIT
N
a
M
ADD
N
4
MbN
:
“
Manual
”
a
M
SELECT
N
5
Enter the desired name.
a
M
OK
N
6
Enter the desired number.
a
M
OK
N
a
M
SELECT
N
R
“
Baby monitor
”
will be displayed.
Note:
R
The registered name/number is displayed.
Turning off the baby monitor
The monitored handset cannot be used while baby
monitor is set to
“
On
”
.
Handset
1
Press
M
MENU
N
on the handset being
monitored.
2
MbN
:
“
On/Off
”
a
M
SELECT
N
3
MbN
:
“
Off
”
a
M
SELECT
N
a
M
OFF
N
34
For assistance, visit www.panasonic.ca/english/support
Programming
TGF3xxC(en)_1216_ver011.pdf 34
2014/12/16 19:11:01