Items
Adjustment Point
Procedure
Check or
Replace Parts
(H)*
DTMF Generator
Confirmation
-
1.
Connect CN1 (Telephone Socket) to DTMF tester.
2.
Execute the command "hookoff" and "dtmf_Hi".
3.
Confirm that the high frequency (1477.06Hz) group is -3dBm ± 2dB.
4.
Execute the command "dtmf_lo".
5.
Confirm that the low frequency (852.05Hz) group is -6dBm ± 2dB.
IC2, R39, C41,
R49, C46, C47,
R43, R44, R45,
R46, R47, R48,
C40, C108,
C109,C36, R42,
Q8, D4, R34
(I)*
Transmitted Power
Confirmation
-
Remove the Antenna before starting step from 1 to 7.
1.
Configure the DECT tester (CMD60) as follows;
<Setting>
·
Test mode: FP
·
Traffic Carrier: 5
·
Traffic Slot: 4
·
Mode: Loopback
·
PMID: 0000
·
RF LEVEL = -70dBm.
2.
Execute the command "testmode".
3.
Execute the command “sendchar dmv 2 2“.
4.
Check that “Signalling Status” has been set to “Locked“, then press
“ACCEPT RFPI“.
5.
Initiate connection from Dect tester (“set up connect“)
6.
Execute the command “ant0“.
7.
Confirm that the NTP value at ANT is 20dBm ~ 25dBm.
IC2, IC4, L1,
C63,
C84, C71, C73,
C104, C62,
C59,
C64, C100,
C58,
C57, C105,
C54,
C55, C82, C72,
R59, R60, R61,
R112, R113,
R91, R92,
L3, DA1
(J)
Modulatoin Check
and Adjustment
ANT
Follow steps 1 to 6 of (I) above.
7.Confirm that the B-Field Modulation is 360kHz/div ~ 380kHz/div using data
type Fig31.
8.Adjust the B-Field Modulation if required. (Execute the command
"readmod" and "wrtmod xx", where xx is the value.)
IC2, IC4, L1,
C63,
C84, C71, C73,
C104, C62,
C59,
C64, C100,
C58,
C57, C105,
C54,
C55, C82, C72,
R59, R60, R61,
R112, R113,
R91, R92,
L3, DA1
(K)
Frequency Offset
Confirmation
-
Follow steps 1 to 6 of (I) above.
7.Confirm that the frequency offset is < ± 50kHz.
IC2, IC4, L1,
C63,
C84, C71, C73,
C104, C62,
C59,
C64, C100,
C58,
C57, C105,
C54,
C55, C82, C72,
R59, R60, R61,
R112, R113,
R91, R92,
L3, DA1
(L)
Frequency Dirft
Confirmation
-
Follow steps 1 to 6 of (I) above.
7.Confirm that the frequency drift is < ± 30kHz/ms.
IC2, IC4, L1,
C63,
C84, C71, C73,
C104, C62,
C59,
C64, C100,
C58,
C57, C105,
C54,
C55, C82, C72,
R59, R60, R61,
R112, R113,
R91, R92,
L3, DA1
54
KX-TCD510RUM / KX-TCD510R UT / KX-TCD510R UV / KX-TCD512R UM / KX-TCD512R UT / KX-TCD512RUV
Содержание KX-TCD510RUM
