Panasonic KX-NS500 Скачать руководство пользователя страница 20

Страница: 20 / 580

2.1 Incoming Call Features

2.1.1 Incoming Trunk Call Features

2.1.1.1 Incoming Trunk Call Features—SUMMARY

Description

Incoming calls via a trunk (public line) are distributed to their destinations according to one of several distribution
methods.

Available Networking Type for Each Card Type

Each trunk port of an optional trunk card or the mother board can be assigned a networking type: Public,
Private, or VPN (Virtual Private Network).

Card Type

Channel/

Protocol Type

Networking Type

Public (DIL/DID/

DDI/MSN)

Private (TIE)

Virtual Private

Network (VPN)

Mother Board
(V-IPGW)

H.323

Mother Board
(V-SIPGW)

SIP

LCOT

—

BRI/PRI

Extension

QSIG-Master

QSIG-Slave

DR2

*: Enable (default);

: Enable

4.3.1 TIE Line Service

4.3.3 ISDN Virtual Private Network (ISDN-VPN)

Distribution Method

One of the following methods can be assigned to each trunk port:

Method

Description & Reference

Direct In Line (DIL)

Directs a call to a preprogrammed single destination (e.g., the
operator).

2.1.1.2 Direct In Line (DIL)

Direct Inward Dialling (DID)

Directs a call with a DID number from a DID line to a preprogrammed
destination.
DID is also known as Direct Dialling In (DDI).

2.1.1.3 Direct Inward Dialling (DID)/Direct Dialling In (DDI)

Feature Guide

2.1.1 Incoming Trunk Call Features

Содержание KX-NS500





































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание KX-NS500

Отзывы:

Похожие инструкции для KX-NS500

Бренды по названию

Популярные бренды

Panasonic KX-NS500, Руководство по функциям

Результаты поиска

Содержание KX-NS500

Отзывы:

Похожие инструкции для KX-NS500

Бренды по названию

Популярные бренды