Panasonic KX-FP207, Руководство по обслуживанию

Страница: 63 / 232

63
KX-FP207FX-S/FP218FX-S
11.1.3. Service Function Table
Code Function Set Value Effective
Range
Default Remarks
501 Pause time set X 100 msec 001~600 30 ----------
503 Dial speed select 1: 10 pps
2: 20 pps 1, 2 1 ----------
510 VOX time (KX-FP218) 1:8sec
2:6sec
3:4sec 1~3 2 ----------
511 VOX sense (KX-FP218) 1:High 2:Low 1, 2 1 When the TAM (or EXT TAM) does not stop recording
the ICM because noise is detected on the telephone
line, change this setting to "LOW".
514 Bell detection time X 100 msec 1~9 6 ----------
520 CED frequency select 1:2100 Hz
2:1100 Hz 1, 2 1 See Symptom/Countermeasure Table for long distance
and international calls in
The unit can copy, but can-
not either transmit/receive long distance or interna-
tional communications
(P.93).
521 International mode select 1:ON 2:OFF 1, 2 1 See Symptom/Countermeasure Table for long distance
and international calls in
The unit can copy, but can-
not either transmit/receive long distance or interna-
tional communications
(P.93).
522 Auto standby select 1:ON 2:OFF 1, 2 1 The resolution reverts to the default when transmission
is complete.
523 Receive equalizer select 1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km 1~4 1 When the telephone station is far from the unit or recep-
tion cannot be performed correctly, adjust accordingly.
524 Transmission equalizer select 1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km 1~4 1 When the telephone station is far from the unit or trans-
mission cannot be performed correctly, adjust accord-
ingly.
544 Document feed position adjustment
value set 1~9 mm 1~9 5 When the ADF function is in correct, adjust the feed
position.
550 Memory clear See Memory Clear Specification (P.66).
551 ROM check See Test Mode (P.58).
552 DTMF single tone test 1:ON 2:OFF 1, 2 2 See Test Mode (P.58).
553 Monitor on FAX communication
select 1:OFF
2:PHASE B
3:ALL 1~3 1 Sets whether to monitor the line signal with the unit's
speaker during FAX communication or not.
554 Modem test See Test Mode (P.58).
555 Scan check See Test Mode (P.58).
556 Motor test 0 See Test Mode (P.58).
557 LED test See Test Mode (P.58).
558 LCD test See Test Mode (P.58).
559 Document jam detection select 1:ON 2:OFF 1, 2 1 Sets whether or not to detect a paper jam. If a docu-
ment with a length longer than 600 mm is copied or
transmitted, the unit stops copying or transmitting as a
paper jamming because a document over 600 mm is
not normal. In the factory, transmitting or copying a doc-
ument longer than 600 mm is done as an aging test. In
this case, OFF is selected.
561 KEY test See Test Mode (P.58).
567 T0 timer X second 001~255 046 Sets a higher value when the response from the other
party needs more time during automatic FAX transmis-
sion.
570 BREAK % select 1:61% 2:67% 1, 2 1 Sets the % break of pulse dialling according PBX.
571 ITS auto redial time set X number of
times 00~99 11 Selects the number of times that ITS is redialled (not
including the first dial).
572 ITS auto redial line disconnection
time set X second 001~999 040 Sets the interval of ITS redialling.
573 Remote turn-on ring number set (KX-
FP207) X number of
rings 00~99 10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
573 Remote turn-on ring number set (KX-
FP218) X number of
rings 00~99 10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
574 Dial tone detect check 1:ON 2:OFF 1, 2 2 ----------