1. GENERAL PRECAUTIONS
1.1. Safety Precautions
1. Before servicing, unplug the power cord to prevent electrical shock hazard.
2. When replacing parts, user only manufacture’s recommended components for
safety.
3. Check the condition of power cord. Replace if wear or damage is evident.
4. After servicing, be sure to restore the lead dress, insulation barriers,
insulation papers, shields, etc.
5. Before returning the serviced equipment to the customer, perform the
following electrical tests to prevent shock hazard.
1.2. Electrical Tests
1. Unplug the power cord and check for continuity between the earth ground
connection on the plug and the Interface Board Cover. There should be zero
ohm resistance.
2. With the unit unplugged, short the AC live-neutral of the plug with a jumper
wire.
3. Turn ON the power switch.
4. Measure the resistance value with an ohmmeter between the jumpered AC
plug and an exposed metal cabinet part, such as screwheads, etc. (Refer to
Fig.2)
Note
Some exposed parts may be isolated from the chassis by design. They read
infinity.
5. If the measurement is less than 1M , a possibility for electric shock may exit.
Note
This hazardous condition must be corrected before the unit is returned to the
end user.
2
Содержание KV-SS905C
