INSTRUCTION MANUAL
Digital Fiber Sensor For Leak / Liquied Detection Fiber
FX-301(P)-F
MJE-FX301F No.0034-46V
Thank you very much for purchasing Panasonic products.
Please read this Instruction Manual carefully and thoroughly for the correct
and optimum use of this product.
Kindly keep this manual in a convenient place for quick reference.
Make sure to connect the fiber attachment (
FX-AT4
), enclosed with the
method.
-
pletely.
!
(
FX-AT4
) slowly into the fiber inlet till it stops
(Note).
" -
tion, till it stops.
# $% &
the sensing becomes unstable.
2
1
3
Fiber lock
lever
Fiber attachment
Fiber
MOUNTING
2
1. Fit the rear part of the mounting section of the
"'*#
2. Press down the rear part of the mounting section
"'*#
front part of the mounting section to the DIN rail.
35mm width DIN rail
1
2
# $%
on the rear portion of the mounting section is likely to break.
+
! 7
1
2
PART DESCRIPTION
1
Operation indicator
(Orange)
MODE indicator / RUN (Green)
MODE key
Jog switch
MODE indicator / TEACH (Yellow)
MODE indicator
OUT (Yellow)
MODE indicator / ALL (Yellow)
MODE indicator / ADJ (Yellow)
MODE indicator / DISP (Yellow)
Digital display (Red)
Model indicator (Green)
MODE key
Jog switch
Press
Press
Turn to “+” side
Turn to“–” side
Used for mode se-
lection or cancella-
tion during setting.
(Note)
U s e d t o s e l e c t
each item.
Used to enter each item.
Note: When MODE key is pressed for 1 sec., or more, the sensor returns to the RUN mode.
(in MAIN mode only)
9 Never use this product as a sensing device for personnel protection.
9 In case of using sensing devices for personnel protection, use products
which meet laws and standards, such as OSHA, ANSI or IEC etc., for
personnel protection applicable in each region or country.
1. Holding the connector of the quick-connection
cable, align its release lever with the groove
2. Insert the connector till a click is felt.
CONNECTION
3
Note: Take care that if the connector is pulled out without pressing the release lever, the re-
lease lever may break. Do not use a quick-connection cable whose release lever has
broken. Further, do not pull by holding the cable, as this can cause a cable-break.
1. Pressing the release lever at the top of the
quick-connection cable connector, pull out the
connector.
Terminal No.
Terminal name
1
+V
2
0V
3
Output
Make sure to connect or disconnect the quick-connection cable in the
power supply off condition.
Groove
Quick-connection
cable
Release
lever
Release
lever
1
2
3
CASCADING AMPLIFIERS
4
9 Make sure that the power supply is off while adding or removing the am-
9 Make sure to check the allowable ambient temperature, as it depends
9
mount them on a DIN rail.
9 ; *#
fit them between the optional end plates (
MS-DIN-E
) mounted at the
two ends.
9 < = ' > ? -
nected in cascade).
9 When connecting more than two amplifiers in cascade, use the sub
cable (
!"#
) as the quick-connection cable for the second ampli-
9 ;
to mount the optional end plate (
MS-DIN-E
) at both sides of each ampli-
= &
protection seal (
FX-MB1
) to the communication windows.
9 Communication function is different between this amplifier and other
=
the communication window seal of the accessory amplifier protection
seal (
FX-MB1
) to the communication windows.
9 In case of cascading, wait for 10 minutes, or more, to use the teaching
function after the power is switched on.
&
"'*#
! =
other, and connect the quick-
connection cables.
3. Mount the optional end plates
(
MS-DIN-E
) at both the ends to
@
B % =
plates.
1. Loosen the screws of the end
plates.
2. Remove the end plates.
3. Slide the amplifiers and remove
them one by one.
Z [
MOUNTING
.”
Sub cable
(
!"#
) (Optional)
End plate
(
MS-DIN-E
) (Optional)
End plate
(
MS-DIN-E
) (Optional)
Main cable
(
!$#
) (Optional)
Slide
Slide
