background image

Unpacking/

Installation

6-1

Section VI
Unpacking/Installation

6.1 Installation requirements

 •

The same as the copier, FA-S620/S660 is a precision machine. The performance

of the sorter can be affected by the surrounding conditions.

(1)

The sorter should not be installed under the following conditions:

(1) Extremely high temperature/humidity.

(2) In areas exposed to direct sunlight.

(3) In areas of high dust concentration.

(4) In areas with poor ventilation.

(5) In areas of chemical fume concentration.

(6) In areas with excessive vibrations.

(7) Directly in air conditioning flow.

Note: If the copier is installed under the above conditions, suggest that the

customer move it to an appropriate place.

(2)

Check the following requirements before installing FA-S620/S660.

(1) The space shown below is needed for installation.

(2) Make sure that only accessories made by Panasonic are used.

• System consoles:

FA-DS72

FA-DS82

(3) Make sure the copier is operating normally before installing FA-S620/

S660.

59.1/1500mm

47.2"/1200mm

39"/100mm

Содержание FP-7818



















































































































































































































































































































































































































Отзывы: