background image

15

English

16

English

 Taking a Reading

Advice:

In general, blood pressure measurements are lower on the second 

attempt because you are calmer.

For people who easily get tense, measuring twice each time is advised.

When two measurements are taken, normally the smaller 

measurement is stored.

When taking two measurements, always stay quiet for 4 to 5 minutes 

after the first measurement before taking the second measurement.

Getting into the proper position for taking a measurement

Place the main unit on a table so that it is flat and the center of 

the unit is at heart height.

*Differences in height will cause differences in blood pressure values.

If the heights of the chair and table are not suitable, you may have to lean 

forward. In this case, form a stable stack of books or similar objects under 

the main unit to adjust the height of the main unit.

*You cannot use the unit while lying down. Use only in a sitting position.

Elbow rest

1  Put the main unit on a table in front of you 

and slide your arm through the 
measurement section of the unit.

Remove your shirt or roll up your sleeve so 

that the measuring section will be on your 

bare skin.

If rolling up your sleeve causes pressure on 

your arm or underarm, remove your shirt for 

measurements.

Be sure that the rolled-up sleeve is not 

inside the cuff area when taking 

measurements.

2  Place your elbow on the elbow rest with 

your palm up and relax.

3  Place the wireless display in front of your 

body where you can see it easily.

The main unit and the wireless display 

transmit/receive the measured values 

through infrared rays. (See page 18.)

Do not put your hand or any other objects in 

front of the wireless display.

Differences in blood pressure values between 

the left and right arms may be around 

10 mmH

g

. The blood pressure can be 

measured in either the left or right arm, but all 

measurements should be taken using the 

same arm for comparative consistency.

Posture to obtain accurate measurements

Stretch your back.

Place the main unit in 

front of you on a table 

at heart height.

Measure on bare skin.

Put your elbow on the elbow rest.

Put your palm up and relax.

Place the wireless display where 

you can see it easily.

Do not put your hand or any other 

objects in front of the wireless display.

Cautions to obtain accurate measurements

Sit quietly and relax while taking measurements.

Do not lean forward 

with your body at an 

angle during 

measurements.

Take measurements in 

the proper posture.

Do not let your rolled-

up sleeve be inside the 

measuring section.

Roll your sleeve far up 

your arm.

Do not take 

measurements at the 

elbow. Place your elbow 

in the elbow rest.

   15-16

2008/01/15   14:54:26

Содержание EW3153





































Отзывы: