About the LCD panel
The LCD panel shows the remaining battery capacity from 0% to 100%,
in 10% increments.
While charging
After charging is
completed
10 minutes after
charging is completed
The indicators glow.
The indicators blink
once every second.
The indicators blink
once every 2
seconds.
During use
After use
min.used
min.used
The used time is shown.
The indicators turn off after 5 seconds.
The shown time returns to [0’00”]
after 10 minutes.
•
•
The used time and the
remaining battery capacity
are shown alternately after
turning off the shaver.
When the battery capacity is low
You can shave 1 to 2 times after “10%” appears.
(This will differ depending on usage.)
•
“10%” appears and
blinks.
A full charge will supply enough power for approx. 14 shaves of 3
minutes each.
•
Using the shaver
Sha
ve
90˚
1
1
Slide the switch lock
button downwards and
press the OFF/ON
switch.
2
2
Hold the shaver as
illustrated above and
shave.
Start out shaving by applying gentle pressure to your face. Stretch your
skin with your free hand and move the shaver back and forth in the
direction of your beard. You may gently increase the amount of
pressure as your skin becomes accustomed to this shaver. Applying
excessive pressure does not provide a closer shave.
Using the trimmer handle
You can change the pivot action. Also, slide the handle up to “
” when
using the trimmer.
FREE
You can move the
shaver head.
LOCK
FREE
LOCK
You can lock the shaver
head.
Slide the trimmer handle up. Place at a right
angle to your skin and move downwards to
trim your sideburns.
FREE
LOCK
Cleaning
Clean
We recommend that you clean your
shaver with the turbo mode for “sonic”
vibration cleaning when the faucet
symbol
appears on the LCD panel.
1. Disconnect the power cord from the
shaver.
2. Apply some hand soap and some
water to the outer foil.
3. Slide the switch lock button
downwards to unlock the OFF/ON
switch.
4. Press the OFF/ON switch for more
than 2 seconds to activate the turbo
mode for “sonic” vibration cleaning.
appears on the LCD panel.
After about 20 seconds, it will be
automatically turned off, or you
can turn it off by pressing the
OFF/ON switch.
5. Remove the outer foil section and
press the OFF/ON switch for more
than 2 seconds to activate the turbo
mode for “sonic” vibration cleaning
and clean it with running water.
6. Wipe off any drops of water with a
dry cloth.
•
•
7
7. Dry the outer foil section and the
shaver completely.
8. Attach the outer foil section to the
shaver.
9. Lubricate the shaver.
Caution for turbo mode
Shaving in turbo mode may damage your skin. Turn the shaver off
and then on again to cancel turbo mode.
Do not place your fingers on the OFF/ON switch while using the
shaver. This may cause the shaver to turn off or enter turbo mode.
•
•
Lubrication
To maintain shaving comfort, it is recommended that the oil provided
with the shaver is used.
1. Switch off the shaver.
2. Apply one drop of oil to each of the outer foils.
3. Raise the trimmer and apply a drop of oil.
4. Switch the shaver on, and run it for approximately five seconds.
5. Switch off the shaver, and wipe off any excess oil from the outer
foils with a soft cloth.
Replacing the system outer foil and the inner blades
When
appears on the LCD panel, approx once a year (this will differ
depending on usage). It is recommended to replace the system outer
foil and check the inner blades.
Press the OFF/ON switch for more than 30 seconds to delete
.
system outer foil
once every year
inner blade
once every two years
Replacing the system outer foil
1. Press the foil frame release buttons
and lift the outer foil section
upwards as illustrated.
2. Press the system outer foil release
buttons and pull down the system
outer foil as illustrated.
3. Align the foil frame
mark and
the system outer foil mark and
securely attach together.
The system outer foil cannot be
reversely attached.
Always insert the system outer foil
to the foil frame when attaching to
the shaver.
4. After turning the
mark to the
front, securely attach the outer foil
section to the shaver until it clicks.
•
•
2
3
•
Replacing the inner blades
1. Press the foil frame release buttons
and lift the outer foil section
upwards as illustrated.
2. Remove the inner blades one at a
time as illustrated.
Do not touch the edges (metal
parts) of the inner blades to
prevent injury to your hand.
3. Insert the inner blades one at a
time until they click as illustrated.
•
2
3
Cleaning with the brush
(A)
(B)
1. Clean the inner blades using the
short brush by moving it in direction
(A).
Clean the system outer foil, the
shaver body and the trimmer using
the long brush.
Do not move the short brush in
direction (B) as it will damage the
inner blades and affect their
sharpness.
Do not use the short brush to
clean the outer foils.
•
•
Removing the built-in rechargeable battery
Remove the built-in rechargeable battery before disposing of the shaver.
Please make sure that the battery is disposed of at an officially
designated location if there is one. Do not dismantle or replace the
battery so that you can use the shaver again. This could cause fire or
an electric shock. Replace it at an authorised service center.
Disconnect the power cord from the shaver when removing the
battery.
Perform steps
1
to
4
and lift the battery, and then remove it.
For environmental protection and recycling of materials
This shaver contains a Lithium-ion battery.
Please make sure that the battery is disposed of at an officially
assigned location, if there is one in your country.
•
•
6
7
4
5
