4
5
6
7
Using the carrying holder
The shaver can be kept vertically or horizontally. When
transporting the shaver, you can use the carrying holder to
protect the outer foil and prevent erroneous operation of the
switch.
•
When transporting the shaver, be sure to clean off any
shavings before attaching the carrying holder.
Attaching the carrying holder
Attach the carrying holder as illustrated.
•
Check that all four protrusions on the shaver are
inserted securely.
Removing the carrying holder
Remove the carrying holder while pressing down
on both sides.
Charge
Charging the shaver
Perform the following steps to charge the shaver if it seems to lose
the speed.
You can charge the shaver with the carrying holder attached.
1
1
Turn off the shaver and insert
it in the AC adaptor until it
clicks as illustrated.
•
Wipe off any water droplets on the side
terminals.
•
If you charge the shaver with power switch
turned on, it will start working when you
remove from the AC adaptor.
2
1
2
2
Put the plug into a household outlet.
The charge indicator lamp glows red.
•
Charging is completed after approx. 8 hours.
•
When charging the shaver for the first time or when it has not
been in use for more than 6 months, the charge indicator lamp
may not glow for a few minutes, or the operating time may
shorten. Please charge it for more than 20 hours in such cases.
3
3
Disconnect the plug after charging is
completed.
•
Charging the battery for more than 8 hours will not affect battery
performance.
•
Recommended ambient temperature for charging is 0 - 35 °C.
The battery may not charge properly or at all under extreme low
or high temperatures.
•
The charge indicator lamp glows and stays on until the plug is
disconnected from a household outlet.
•
A full charge will supply enough power for approx. 7 shaves of 3
minutes each. (This will differ depending on usage.)
You cannot operate the shaver while charging.
Shave
Using the shaver
1
1
Press the power
switch.
2
2
Hold the shaver as
illustrated above and
shave.
Start shaving by applying gentle pressure to your face. Stretch
your skin with your free hand and move the shaver back and
forth in the direction of your beard. You may gently increase the
amount of pressure as your skin becomes accustomed to this
shaver. Applying excessive pressure does not provide a closer
shave.
You can also use a pen grip to hold
the shaver.
Caution
•
Before shaving, check that the cleaning shutter is closed.
•
Do not place your fingers on the power switch while using the
shaver. This may cause the shaver to turn off.
•
Do not use shaving creams or face cleansers containing
scrubbing compounds as these may cause the outer foil to
clog.
Using the trimmer
Slide the trimmer handle up. Place
at a right angle to your skin and
move downwards to trim your
sideburns.
•
We recommend using the shaver in an ambient temperature
range of 0 - 35 °C. If used outside this range, the appliance may
stop operating.
Clean
Cleaning the shaver
1. Remove the shaver from the AC adaptor.
2. Apply some hand soap and some water
to the outer foil.
•
Close the cleaning shutter.
3. Turn the shaver on.
3
Cleaning with the brush
Clean the system outer foil, the
shaver body and the trimmer using
the long brush.
Clean the inner blades using the
short brush by moving it in direction
(A).
•
Do not move the short brush in
direction (B) as it will damage the
inner blades and affect their
sharpness.
•
Do not use the short brush to
clean the outer foils.
(A)
(B)
Replacing the system outer foil and the inner blades
system outer foil
once every year
inner blades
once every two years
Removing the outer foil section
Press the foil frame release button and lift the outer foil section
upwards.
Attaching the outer foil section
After turning the water inlet surface to the front,
securely attach the outer foil section to the
shaver until it clicks.
1
2
▼
▼
To remove light dirt
For heavy dirt
4. Slide the cleaning shutter
until it clicks.
5. Clean the outer foil section
with running water.
6. Turn the shaver off.
•
Rinse with water and
shake up and down
several times to remove
the water.
4. Turn the shaver off after
10 - 20 seconds.
5. Remove the outer foil
section and turn the shaver
on.
6. Clean the shaver and the
outer foil section with
running water.
•
Rinse with water and
shake up and down
several times to remove
the water.
▼
▼
7. Wipe off any drops of water with a dry
cloth.
8. Dry the outer foil section and the shaver
completely in a shaded area.
9. Attach the outer foil section to the shaver.
•
Open the cleaning shutter.
•
The outer foil section will dry faster if
removed from the main body.
8
►
Replacing the system outer foil
1. Press the system outer foil release buttons
and pull down the system outer foil.
2. Align the water inlet surface and the system
outer foil mark ( ) and securely attach
together.
•
The system outer foil cannot be reversely
attached.
•
Always insert the system outer foil to the
foil frame when attaching to the shaver.
►
Replacing the inner blades
1. Remove the inner blades one at a time.
•
Do not touch the edges (metal parts) of
the inner blades to prevent injury to your
hand.
2. Insert the inner blades one at a time until
they click.
►
Replacement parts
Replacement parts are available at your dealer or Service Center.
Replacement parts
for ES-SL41
System outer foil and inner blades WES9013
System outer foil
WES9087
Inner blades
WES9068
Removing the built‑in rechargeable battery
Remove the built-in rechargeable battery before disposing of the
shaver. Please make sure that the battery is disposed of at an
officially designated location if there is one. Do not dismantle or
replace the battery so that you can use the shaver again. This
could cause fire or an electric shock.
Please contact an authorised service center.
•
Remove the shaver from the AC adaptor when removing the
battery.
•
Perform steps
1
to
;
and lift the battery, and then remove it.
For environmental protection and recycling of materials
This shaver contains a Nickel-Metal Hydride battery.
Please make sure that the battery is disposed of at an officially
assigned location, if there is one in your country.
Specifications
Power source
See the name plate on the AC adaptor.
Motor voltage
1.2 V
Charging time
230 V
Approx. 10 hours
240 V
Approx. 8 hours
This product is intended for household use only.
