background image

©

2001 Matsushita Electric Works, Ltd. All rights

reserved. Unauthorized copying and distribution is a
violation of law.

EP1022-U1

MASSAGE LOUNGER

SPECIFICATIONS

Power source

: 120V AC, 60Hz

Power consumption

: 120W

Kneading speed

: Approx. 28 times/min.

Tapping speed

: Approx. 500 times/min.(per side)

Rolling massage speed

: Approx. 1 cycle every 37 sec.

Massaging width

: Shoulder/lower back section : Approx. 2-15/16 in. (75mm)

Back rolling width/tapping width

: Narrow : Approx. 3-5/16 in. (85mm)
: Wide : Approx. 4-5/16 in. (110mm)

Massage heads up/down travel

: Approx. 23-1/16 in. (600mm)

Regional back rolling

: Automatic repetition within approx. 4-12/16 in. (120mm) range

Shoulder position adjustment

: 5 steps

Automatic shut-off

: Approx. 15 min.

Dimensions (H x W x D)

:

!

Not reclined and leg rest retracted : 41-11/32X34-41/64X40-35/64 in.(1050X880X1030mm)

!

Reclined and leg rest extended : 29-9/64X34-41/64X68-7/64 in.(740X880X1730mm)

Reclining angle

: Approx. 123° to 160°

Weight

: 102 lbs. (46kg)

Accessories

: Back cushion, Headrest, Cushion pad

ORDER NO.HPD0104U00C1

Содержание EP1022-U1


















































Отзывы: