Panasonic EASA-PHONE KX-T123210 страница 207 Скачать руководство пользователя

Страница: 207 / 242

To set

. . . . . . . until the desired DTMF receiver appears

: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

: receiver 1

: receiver 2

To confirm

: receiver 3

Dial any extension (100 through 199) and listen for that extension to ring.

Description

DTMF (Dual Tone Multi Frequency) Receiver

enables tone telephones to dial within the system.

To check the DTMF Receivers, activate the DTMF

Receivers one at a time and confirm if the receiver

can receive tone signals.

at Extension Connected to Jack

Number 1.

To Remove DTMF Receive 2 and 3:

1. Set-the System Program Switch on the

KX-I123210 to the “PITS” position.

2. Dial (30) to enter the DTMF mode.

“DTM F Receiver” will be displayed.

3. Press the NEXT button.

“DTMF-R

will be displayed.

4. Press the NEXT button, twice, or dial (2).

: Enable” will be displayed.

5. Press the SELECT button to change to

“Disable”.

: Disable” will be displayed.

6. Press the MEMORY button.

7. Press the NEXT button, or press the SELECT

button and then dial (3).

: Enable” will be displayed.

8. Press the SELECT button to change to

“Disable”.

9. Press the MEMORY button.

10. Press the END button to return to the initial

program mode.

11.

Set the System Program Switch to the

“SET” position.

Confirmation of DTMF Receiver 1:

Set the DIALING MODE (located on the rear of

KX-T123230) switch to the TONE position.

2. Set the POWER FAILURE (located on the rear

of KX-T123230) switch to the ON position.

3. Dial the extension number (100 through 199).

4. If DTM F Receiver is bad, do the following

procedure for removing the DTMF Receiver

after the next step on this section.

5. Set the POWER FAILURE Switch to the OFF

position.

To check DTMF Receiver 2, remove DTMF

1 and confirm that DTMF Receiver 2 is

good by the procedures of “To Remove DTMF

Receiver 1 and 3” and “Confirmation of DTMF

Receiver 2”.

To check DTMF Receiver 3, remove DTMF

Receiver 1 and confirm that DTMF Receiver 3 is

good by the procedures of “To Remove DTMF

Receiver 1 and 2” and “Confirmation of DTMF

Receiver 3”.

Содержание EASA-PHONE KX-T123210



















































































































































































































































Результаты поиска

Содержание EASA-PHONE KX-T123210

Отзывы:

Похожие инструкции для EASA-PHONE KX-T123210

Бренды по названию

Популярные бренды

Panasonic EASA-PHONE KX-T123210, Руководство по установке

Результаты поиска

Содержание EASA-PHONE KX-T123210

Отзывы:

Похожие инструкции для EASA-PHONE KX-T123210

Бренды по названию

Популярные бренды