79
RQT8346
Channel/Clock settings when TV Guide On Screen
®
system is not used
Refer to the control reference on page 74.
Preparation:
If the program listings has already been downloaded, return the unit to the factory preset condition using the steps indicated below.
When the unit is on and stopped
1
Press and hold [CH,
X
] and [CH,
W
] on the main unit for about 5 seconds.
The unit turns off.
2
Press [
Í
, DVD/VHS POWER] to turn the unit on.
3
After the language and TV aspect is setup, press [RETURN] and exit the TV Guide
On Screen
®
system setup screen.
Note
You can set scheduled recording only manually after you set the unit with “Set Channels
Automatically”.
[1]
While stopped
Press [FUNCTIONS].
[2]
Press [
3
,
4
] to select “Other Functions” and
then press [ENTER].
[3]
Press [
3
,
4
] to select “Setup” and then press
[ENTER].
[4]
Press [
3
,
4
] to select “Channel” and then
press [
1
].
[5]
Press [
3
,
4
] to select “Set Channels
Automatically” and then press [ENTER].
[6]
Press [ENTER].
Auto Channel Setting starts. This takes a few minutes.
The unit then proceeds with Auto Clock Setting. The time is
displayed when finished.
≥
DST, Daylight Saving Time, shows the summertime setting.
≥
TIME ZONE shows the time difference from Greenwich Mean
Time (GMT).
EST (Eastern Standard Time)
l
GMT
j
5
CST (Central Standard Time)
l
GMT
j
6
MST (Mountain Standard Time)
l
GMT
j
7
PST (Pacific Standard Time)
l
GMT
j
8
AST (Alaska Standard Time)
l
GMT
j
9
HST (Hawaii Standard Time)
l
GMT
j
10
For other areas: xx hr
≥
If the Auto Clock Setting does not start automatically, select
“Clock Settings” from the “Setup” tab and then select “Set
Clock Automatically”.
≥
If the time was not set correctly, use manual clock setting
(
l
25) or adjust time zone.
[7]
Press [ENTER].
≥
Regarding DST (Daylight Saving Time)
l
25
≥
The unit configures channels according to the Signal Source
(RF IN) settings as follows.
Adjust the time zone (
j
1 or
i
1) if it was not set correctly with auto
clock setting.
You cannot change this setting if you set the clock manually.
[1]
While stopped
Press [FUNCTIONS].
[2]
Press [
3
,
4
] to select “Other Functions” and
then press [ENTER].
[3]
Press [
3
,
4
] to select “Setup” and then press
[ENTER].
[4]
Press [
3
,
4
] to select “Setup” and then press
[
1
].
[5]
Press [
3
,
4
] to select “Clock Settings” and
then press [ENTER].
[6]
Press [
3
,
4
] to select “Adjust Time Zone” and
then press [ENTER].
≥
Regarding DST (Daylight Saving Time)
l
25
[7]
Press [
3
,
4
] to select “
s
1” or “
r
1” and then
press [ENTER].
To return to the previous screen
Press [RETURN].
To exit the screen
Press [RETURN] several times.
To cancel partway while Auto Channel/Clock Setting is taking place
Press [RETURN].
To set so the TV Guide On Screen
®
system is not displayed automatically when you turn the unit on
When the power is turned on and the Start setup screen is displayed, press [
3
,
4
] to select “Don’t remind me again” and press [ENTER].
Auto channel/clock settings
Setup
Disc
Channel
Video
Audio
Display
Set Clock Automatically
Auto Clock Setting is complete.
11/4/2006 12:15 AM
DST.............. On
Time Zone..... CST
Setup
Signal Source
(RF IN)
Band
Channel
Antenna
VHF
2 to 13
UHF
14 to 69
CableTV
VHF
2 to 13
CATV LOW BAND
95 to 99
CATV MID/SUPER BAND
14 to 36
CATV HYPER BAND
37 to 65
ULTRA BAND
66 to 94
100 to 125
SPECIAL CATV CHANNEL
1
∫
Adjust Time Zone
Setup
Setup
Audio
Adjust Time Zone
j
1
0
i
1
Channel
Disc
Video
Ch
a
n
g
in
g
th
e
u
n
it’s se
ttin
g
s/C
h
a
n
n
e
l/Cl
o
ck se
ttin
g
s w
h
e
n
T
V
Gu
id
e
On
S
cr
e
e
n
®
syst
e
m
is n
o
t use
d
M6740P.book 79 ページ ２００６年１月３０日 月曜日 午後３時３０分
