29
RQT7751
≥
Even when the unit is turned off, you can display the timer
recording list by pressing [PROG/CHECK].
Press [PROG/CHECK].
∫
To change a programme
Press [
3
,
4
] to select the programme and press [ENTER].
step 3)
∫
To delete a programme
Press [
3
,
4
] to select the programme and press [
¢
CANCEL].
∫
To exit the timer recording list
Press [PROG/CHECK].
∫
To put the unit on timer recording standby
Press [
F
TIMER].
“
F
” lights on the unit’s display to indicate timer recording standby
has been activated.
≥
Programmes that failed to record are deleted from the timer
recording list at 4 a.m. two days later.
[HDD]
[RAM]
[DVD-R]
If an external equipment (for example a satellite receiver) with a
timer function is connected to the AV2 terminal of this unit by a
21-pin Scart cable (
page 9), it is possible to control the recording
of the unit with the equipment.
Preparation
≥
Change the “Ext Link” in the SETUP menu to match the connected
equipment (
≥
Timer programming has to be done on the external equipment and
switch to the timer recording standby mode. Refer to the
equipment’s operating instructions.
≥
Press [HDD] or [DVD] to select the drive.
Press [EXT LINK].
The unit turns off and switches to the recording standby mode.
≥
Recording begins when a signal is received from the connected
equipment.
≥
As long as a video picture is being transmitted by the external
equipment, the unit will record it.
When the following message appears on the television screen, press
[
2
,
1
] to select “Yes” (continue recording the current programme)
or “Cancel” (cancel recording) and press [ENTER].
To cancel the external control
Press [EXT LINK] to stop recording or to cancel linked timer
recording standby.
≥
You can also press and hold [
∫
] on the main unit for more than 3
seconds to stop recording.
≥
In order to prevent accidental operation, press [EXT LINK] to
cancel the setting after recording is finished.
For your reference
≥
The video being recorded automatically appears on the television
when connected to this unit’s AV1 terminal with the 21-pin Scart
cable.
≥
This function does not work with some equipment. Refer to the
equipment’s operating instructions.
≥
The beginnings of recordings may not be recorded correctly in
some cases.
≥
When “Ext Link” is set to “Ext Link 2”, this function does not work if
the input signal is NTSC system.
Check, change or delete a programme
TIMER
RECORDING
12:56:00 15. 7. TUE
SELECT
ENTER
RETURN
Press ENTER to store
new programme.
1:58 SP
DVD
30:24 SP
Remain HDD
Mode
Disc
space
Stop
Start
No.
Name
Date
12:55:00 15. 7. TUE
VPS
PDC
HDD
DVD
New Timer Programme
Icons
[
This programme is currently recording.
W
The times overlap those in another programme.
Recording of the programme with the later start time
starts when the earlier programme finishes recording.
F
The disc was full so the programme failed to record.
The material was copy-protected so it was not recorded.
X
The programme did not complete recording because the
disc is dirty or some other reason.
Timer programmes set to Auto Renewal Recording
(
Titles that have been rerouted to the HDD
(Displayed while recording.)
Recording drive: HDD
Recording drive: DVD
Message displayed in the “Disc space” line
OK:
Displayed if the recording can fit in the
remaining space.
>
(Date):
For recordings made daily or weekly, the display
will show until when recordings can be made (up
to a maximum of one month from the present
time) based on the time remaining on the disc.
! :
It may not be possible to record because:
≥
there is not enough space left
≥
the number of possible titles has reached its
maximum.
Relief:
Timer programmes that will be relief recorded to
the HDD.
Linked timer recordings with external
equipment (EXT LINK)
Yes
Cancel
DVD now recording this programme.
ENTER
RETURN
29
7551-EN.book 29 ページ ２００４年８月２６日 木曜日 午後４時３４分
